Dell PowerVault TL4000 Betriebsanleitung Seite 58
- Seite / 80
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
8.6 Removing and replacing the base chassis
WARNING! The AP Series tape library weighs 24.5 kg without media, and 26.43 kg when both
magazines are full (48 cartridges).
To reduce the risk of personal injury or damage to equipment:
1) Observe local health and safety requirements and guidelines for manual material
handling,
2) Obtain adequate assistance to lift and stabilize libraries during installation or removal,
3) Remove all tapes to reduce the overall weight of the library.
You will need a #3 Phillips screwdriver to remove and replace the base chassis assembly. Before
beginning, be sure the tape drive or drives do not contain a tape cartridge. To remove a cartridge, see
”Moving tapes in the library” on page 48.
To remove the components in the base chassis and the base chassis from the
rack:
1. Obtain adequate assistance to lift and stabilize the library during removal and replacement.
2. Remove the magazines from the library, see ”Removing and replacing a magazine” on page
65.
3. Turn off power to the library and disconnect the power and SCSI cables.
4. Remove the library from the rack:
• From the front of the library loosen the two screws anchoring the mounting brackets on
the library to the rack. These are captive screws and cannot be removed.
• Remove your library from the rack using assistance..
5. Remove the replacement library enclosure from the packing materials.
6. Place the replacement library enclosure on a solid surface in preparation for installation in to
the rack.
7. Remove the mounting brackets and guide pulleys from your library and install them on the
replacement library.
8. Loosen the blue thumbscrews on the power supply, and pull the power supply from your
library.
9. Install the power supply in your replacement library.
10. Loosen the blue thumbscrews on the tape drive, and pull the tape drive handle while
supporting the bottom of the drive to remove from your library.
11. Install your drive in the replacement library enclosure.
12. Loosen the blue thumb screws on the tape drive, and pull the tape drive handle while
supporting the bottom of the drive to remove the drive from the library.
13. Repeat Step 12 if you have a second drive.
14. Loosen the blue thumbscrews on the library controller and remove the controller form the
library.
15. Install the library controller in your replacement library.
16. Remove the yellow label that is securing the lock on the rear panel, and then remove the lock.
17. Store the lock and label to the top cover (see Figure 8).
18. Repeat Steps 16 and 17 with your replacement library.
- Automatic Protection (AP) 1
- User and Service Guide 1
- Copyright 2
- Trademark Notices 2
- Contacting PivotStor, LLC 2
- About this guide 3
- 1 Warnings and symbols 4
- 1.1 Precautions 5
- 1.3 Rack stability 5
- 2 Contents 6
- 3 Figures 8
- 4 Tables 10
- 5.2 SCSI requirements 12
- 5.4 LUN scanning 12
- Back panel overview 16
- 5.6 Installing the library 18
- SCSI cable 19
- Rack mount kit: 19
- Documentation CD 19
- Library 19
- Terminator 19
- 6.1 Operating Modes 26
- 6.2 OCP Philosophy 26
- 6.3 Power-Up Display 26
- Idle Rand 27
- 6.4 Note about the LED’s 28
- 6.5 Input Modes 28
- 6.6 Power ON/OFF 29
- Robotic Drive 1 30
- AP Series 31
- PivotStor 31
- Commands 32
- Open Mailslot 32
- Service Menu 34
- Library Veryfy 34
- Run Test Service 34
- 6.8 Tape cartridges 35
- Tape’s media pool 36
- Data residing on the tape 36
- Age of the backup 36
- 1 Write-enabled 37
- 2 Write-protected 37
- 3 Write-protect switch 37
- Barcode label 37
- Insertion arrow 37
- 7.1 Overview 40
- 7.3 Library status icons 41
- 7.4 Login 41
- 7.5 Identity 42
- 7.6 Status 43
- 7.7 Configuration 44
- IP Address 45
- Network Mask 45
- Gateway Address 45
- Setting date/time 47
- Setting error log mode 47
- 7.8 Operations 48
- 7.9 Service 50
- 8.1 Possible tools needed 53
- 8.2 Electrostatic Discharge 53
- To remove a power supply: 56
- 9 Troubleshooting 60
- 9.2 Troubleshooting table 61
- 9.3 Service Procedures 64
- AP Series Remote Management 66
- Right magazine release 67
- Left magazine release 67
- Example error code 68
- 10 Technical specifications 74
- 11 Regulatory Information 76
- 12 Index 78
Verwandte Produkte und Handbücher für Vernetzung Dell PowerVault TL4000
Vernetzung Dell PowerEdge T710 Spezifikationen
(63 Seiten)
(63 Seiten)
Vernetzung Dell PowerEdge T420 Spezifikationen
(51 Seiten)
(51 Seiten)
Vernetzung Dell PowerEdge M710 Spezifikationen
(31 Seiten)
(31 Seiten)
Vernetzung Dell Vostro 420 Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Vernetzung Dell PowerEdge R210 Spezifikationen
(72 Seiten)
(72 Seiten)
Vernetzung Dell PowerEdge R815 Spezifikationen
(59 Seiten)
(59 Seiten)
Vernetzung Dell PowerEdge T310 Spezifikationen
(57 Seiten)
(57 Seiten)
Vernetzung Dell PowerEdge T310 Spezifikationen
(49 Seiten)
(49 Seiten)
Vernetzung Dell PowerEdge R720xd Bedienungshandbuch
(165 Seiten)
(165 Seiten)
Vernetzung Dell TL24iSCSIxSAS Betriebsanweisung
(16 Seiten)
(16 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.116 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern