Dell PowerVault TL4000 Betriebsanleitung Seite 28
- Seite / 80
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6.4 Note about the LED’s
All LEDs are updated during Power Up and Reset sequences. Upon power up or software Reset, the
loader will illuminate all LEDs as soon as POST allows. This will help the User to verify if all LEDs are
functional. When initialization starts, all LEDs will be extinguished and the Ready/Activity LED will flash
at a reasonable rate of approximately 1-second per cycle, 50% duty cycle. When the mechanical
initialization is complete, the Ready/Activity LED will stop flashing and be constantly illuminated.
If a loader failure occurs, the Ready/Activity LED will be turned off and the Error LED will be illuminated.
The Op Panel will also display an appropriate error code to help identify the failure.
The following are additional operational details of LEDs.
• The “Ready/Activity” LED will be lit any time the unit is powered on and functional (i.e. passed
power-on self-test). The Ready/Activity LED will blink whenever there is tape library or drive
activity. This LED will also blink when the unit is Offline.
• The "Clean" LED will only be lit when a cleaning REQUIRED has been issued by the drive. The
LED will be turned off again after a successful drive cleaning operation.
• The "Media Attention" LED will indicate that there is a piece of media which is bad/marginal, or
invalid. The LED will be cleared when all marginal and invalid cartridges have been exported
from the tape library.
• The "Error" LED will be lit when there is an unrecoverable (i.e. hard) drive or tape library failure.
This will happen at the same time the hard error message is displayed on the screen and the
LED will remain lit until the error state is resolved.
6.5 Input Modes
There are several modes to enter values in the different menu items. These values are selectable
predefined values, toggle values (e.g. On/Off) and numerical values like network addresses.
Selectable predefined values
After navigating to the menu item the various predefined values can be selected with the NEXT and
PREVIOUS button. As soon as the display shows the correct value it may be confirmed by pressing the
“ENTER” button.
Toggle values
Toggle values are used to switch between two different states like On and Off. After navigating to the
menu item the display shows the actual state. Pressing the ENTER button will switch to the possible new
state. Pressing ENTER a second time will take over this new state.
Numerical values
Numerical values are needed for network addresses, PIN entries, and other configuration entries. After
navigating to the menu item to be changed, the actual value will be displayed and the cursor stays on
the first digit. The value may be incremented / decremented with the NEXT and PREVIOUS button. After
pressing the ENTER button the cursor is set to the next editable digit. It can be changed in the same
way. After pressing the ENTER button at the last digit the complete entry will be stored. Pressing the
CANCEL button will cancel the whole edit process and the old value is valid again.
- Automatic Protection (AP) 1
- User and Service Guide 1
- Copyright 2
- Trademark Notices 2
- Contacting PivotStor, LLC 2
- About this guide 3
- 1 Warnings and symbols 4
- 1.1 Precautions 5
- 1.3 Rack stability 5
- 2 Contents 6
- 3 Figures 8
- 4 Tables 10
- 5.2 SCSI requirements 12
- 5.4 LUN scanning 12
- Back panel overview 16
- 5.6 Installing the library 18
- SCSI cable 19
- Rack mount kit: 19
- Documentation CD 19
- Library 19
- Terminator 19
- 6.1 Operating Modes 26
- 6.2 OCP Philosophy 26
- 6.3 Power-Up Display 26
- Idle Rand 27
- 6.4 Note about the LED’s 28
- 6.5 Input Modes 28
- 6.6 Power ON/OFF 29
- Robotic Drive 1 30
- AP Series 31
- PivotStor 31
- Commands 32
- Open Mailslot 32
- Service Menu 34
- Library Veryfy 34
- Run Test Service 34
- 6.8 Tape cartridges 35
- Tape’s media pool 36
- Data residing on the tape 36
- Age of the backup 36
- 1 Write-enabled 37
- 2 Write-protected 37
- 3 Write-protect switch 37
- Barcode label 37
- Insertion arrow 37
- 7.1 Overview 40
- 7.3 Library status icons 41
- 7.4 Login 41
- 7.5 Identity 42
- 7.6 Status 43
- 7.7 Configuration 44
- IP Address 45
- Network Mask 45
- Gateway Address 45
- Setting date/time 47
- Setting error log mode 47
- 7.8 Operations 48
- 7.9 Service 50
- 8.1 Possible tools needed 53
- 8.2 Electrostatic Discharge 53
- To remove a power supply: 56
- 9 Troubleshooting 60
- 9.2 Troubleshooting table 61
- 9.3 Service Procedures 64
- AP Series Remote Management 66
- Right magazine release 67
- Left magazine release 67
- Example error code 68
- 10 Technical specifications 74
- 11 Regulatory Information 76
- 12 Index 78
Verwandte Produkte und Handbücher für Vernetzung Dell PowerVault TL4000
Vernetzung Dell PowerEdge T710 Spezifikationen
(63 Seiten)
(63 Seiten)
Vernetzung Dell PowerEdge T420 Spezifikationen
(51 Seiten)
(51 Seiten)
Vernetzung Dell PowerEdge M710 Spezifikationen
(31 Seiten)
(31 Seiten)
Vernetzung Dell Vostro 420 Bedienungsanleitung
(72 Seiten)
(72 Seiten)
Vernetzung Dell PowerEdge R210 Spezifikationen
(72 Seiten)
(72 Seiten)
Vernetzung Dell PowerEdge R815 Spezifikationen
(59 Seiten)
(59 Seiten)
Vernetzung Dell PowerEdge T310 Spezifikationen
(57 Seiten)
(57 Seiten)
Vernetzung Dell PowerEdge T310 Spezifikationen
(49 Seiten)
(49 Seiten)
Vernetzung Dell PowerEdge R720xd Bedienungshandbuch
(165 Seiten)
(165 Seiten)
Vernetzung Dell TL24iSCSIxSAS Betriebsanweisung
(16 Seiten)
(16 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.189 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern