Dell Active Fabric Manager Betriebsanweisung Seite 153
- Seite / 179
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4. From the Polling Rate pull-down menu, select the polling rate.
a) 15 Minutes (default)
b) 30 Minutes
c) 45 minutes
d) 1 Hour
5. Check the fabric to collect data from.
6. Click the OK.
Threshold Settings
To configure the monitoring link bundle and Threshold Crossing Alert (TCA) between the spine switches and the leaf
switches for a fabric, use the Jobs > Data Collections > Edit Threshold Settings screen. The Average Traffic Threshold
option monitors the Layer 3 fabric link bundle. The TCA bandwidth option monitors Layer 2 and Layer 3 fabrics low
bandwidth and high bandwidth “In Traffic Utilization” and ”Out Traffic Utilization”.
When the average traffic, low and high utilization thresholds are both exceeded AFM receives an alarm from the switch
on the Alerts > Active Alerts screen.
Average Traffic Threshold Average Traffic Threshold configures the threshold value for a Layer 3 fabric.
The monitoring value is only configured on the fabric link between the spine
and leaf switches.
Range: 60--90%
Low Utilization Low Utilization Threshold sets the value for TCA. When the statistics is set
below the Low utilization, the TCA alarm clears. The graphical performance
monitoring removes a RED solid line with label as “Traffic Utilization Alert
Threshold” from the chart.
Range: 40-60%
High Utilization High Utilization Threshold sets the highest value for TCA. When the statistics
is beyond the threshold, the TCA alarm raises. The behavior from graphical
performance monitor is to draw a RED solid line with label as “Traffic
Utilization Alert Threshold” on the chart.
Range: 60-80%
Job ID When the schedule is created, AFM creates a job ID.
With real-time performance management at the port level, a RED solid line appears on the threshold with the label
“Traffic Utilization Alert Threshold”. This indicates that TCA has exceeded the threshold. When the alarm is cleared, the
RED solid line disappears.
153
- Active Fabric Manager (AFM) 1
- Deployment Guide 2.0 1
- Contents 3
- Introduction 9
- About AFM 11
- Getting Started 13
- Figure 2. Capacity Planning 15
- Figure 3. Provisioning 16
- AFM Site Map 17
- Supported Fabric Types 19
- VLT) Fabric 20
- Conventional Core 21
- Distributed Core 22
- Key Advantages 22
- Distributed Core Terminology 23
- FTOS Configuration Guide 24
- Multi-domain VLT 31
- VLT Terminology 31
- VLT Fabric Terminology 31
- VLT Components 32
- Typical VLT Topology 32
- 10 Gb or 40 Gb ToR (mVLT) 37
- Designing the Fabric 49
- Table 12. Switch Level States 51
- AFM Plug-in for 53
- Openstack 53
- Deployment Topology Use Cases 55
- Use Case 3: 2 Tier Layer 2 57
- Use Case 5: 3 Tier Layer 2 62
- Deleting the Fabric 77
- Viewing the Wiring Diagram 77
- Fabric Deployment Summary 79
- Pre-Deployment Configuration 83
- Pre-Deployment Flowchart 84
- Pre-Deployment Screens 84
- Fabric Name 101
- Fabric Name 105
- AFM Installation Guide 107
- Open Automation Guide 108
- Open Automation Guide 108
- Deploying the Fabric 109
- Advanced Configuration 112
- Associating Templates 113
- Validation 115
- Validating the Fabric 116
- Custom CLI Configuration 117
- Editing Templates 118
- Deleting Templates 118
- Editing Template Associations 120
- Viewing the Fabric 123
- Switch Name 124
- Network Topology 125
- Fabric Summary 127
- Switch Summary 129
- Troubleshooting 131
- Validation Alarms 132
- Pre-deployment Errors 134
- Deployment Errors 134
- Validation Errors 135
- Table 34. Wiring Errors 136
- TFTP/FTP Error 143
- Alerts and Events 145
- Performance Management 149
- Fabric Performance Management 150
- Switch Performance Management 150
- Port Performance Management 151
- Data Collection 152
- Threshold Settings 153
- Creating New Reports 154
- Editing Reports 155
- Running Reports 155
- Duplicating Reports 155
- Deleting Reports 156
- Maintenance 157
- Updating the Switch Software 158
- Replacing a Switch 158
- Step 2: Replacing a Switch 159
- Updating the AFM 160
- Displaying Job Results 163
- Scheduling Jobs 163
- Switch Backup 164
- Switch Software Updates 164
- Switch Software Activation 165
- Administration 169
- Fabric 170
- CLI Credentials 171
- Client Settings 171
- Data Retention Settings 172
- DHCP Server Settings 172
- NTP Server Settings 172
- SMTP Email 173
- SNMP Configuration 173
- Syslog Server IP Addresses 173
- System Information 173
- Managing User Accounts 174
- Adding a User 175
- Deleting a User 176
- Editing a User 176
- Unlocking a User 177
- Changing Your Password 177
- Managing User Sessions 178
- Audit Log 178
Verwandte Produkte und Handbücher für Vernetzung Dell Active Fabric Manager
Vernetzung Dell B-DCX-4s Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Dell Managed PDU LED Bedienungsanleitung
(244 Seiten)
(244 Seiten)
Vernetzung Dell R2 Schnellstart Anleitung
(122 Seiten)
(122 Seiten)
Vernetzung Dell R1 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Dell 3-DNS Einstellungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Dell PowerEdge T620 Spezifikationen
(39 Seiten)
(39 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern