Dell S4810-ON Installationsanleitung

Dell Neworking S4810–Open Networking (ON) Installation GuideApril 2014

• SystemFigure 3. S4810–ON LEDs1. SYS2. MASTER3. FAN4. PSU10The S4810–ON System

3Site PreparationsThe S4810–ON is suitable for installation as part of a common bond network (CBN).You can install the system in:• network telecommuni

Rack MountingWhen you prepare your equipment rack, ensure that the rack is earth ground.Ground the equipment rack to the same ground point the power s

Storing ComponentsIf you do not install your S4810–ON and components immediately, Dell Networking recommends properly storing the system and all optio

14

4Install the S4810–ONTo install the S4810–ON system, Dell Networking recommends completing the installation procedures in the order presented in this

To attach the brackets to the system, follow these steps.1. Take the brackets and screws out of their packaging.2. Attach the brackets to the PSU side

NOTE: Dell Networking recommends using one person to hold the S4810–ON chassis in place while another person attaches the brackets to the posts.Attach

3. Attach the brackets to the PSU sides of the chassis using four screws for each bracket. Attach the bracket so that the “ear” is parallel to the PSU

3. Fasten the system to the PSU-facing posts using rack mount screws (not included with the system).Figure 7. Installing the System into a Four-Post R

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

3. Attach the one-hole lug to the chassis using the supplied 10-32 screw with the captive internal tooth lock washer. Torque the screw to 20 in-lbs.Fi

Remove the SFP+ and QSFP+ OpticsRemove an optic by pushing the tab on the optic and sliding the optic from the port.When removing optics with direct a

Figure 9. AC Power Connection1. Power Connection2. LEDAfter Installing the S4810–ONAfter you have securely installed and powered on the S4810-ON, refe

5Power SuppliesThe S4810–ON supports two hot-swappable power supply units (PSUs) with integrated fans that provide cooling for the system.The S4810–ON

Installing an AC Power SupplyTo install an AC power supply, follow these steps.NOTE: The PSU slides into the slot smoothly. Do not force a PSU into a

Replacing an AC Power SupplyTo replace an AC power supply, follow these steps:NOTE: The PSU slides into the slot smoothly. Do not force a PSU into a s

26

6FansThe S4810–ON comes from the factory with one power supply unit (PSU) and two fan modules installed in the system.If two or more fans are installe

Figure 11. S4810–ON Fan Module1. PSU12. Fan Module 13. Fan Module 24. Grab Handle5. PSU2Installing a Fan ModuleThe fan modules in the S4810–ON are fie

4. Tighten the captive screws on the replacement module with a screwdriver. Ensure that the module is secure.Fans29

Contents1 About this Guide...5Information Symbols

30

7Console PortsYou can access the S4810–ON directly through the console port at the input/output (I/O) side of the system.Accessing the RJ-45 Console P

Access the RJ-45 Console Port with a DB-9 AdapterIf the DTE has a DB-9 interface, you can connect to the console using an RJ-45 to DB-9 adapter along

8SpecificationsThis chapter lists the S4810–ON specifications.Chassis Physical DesignTable 2. Chassis Physical DesignParameter SpecificationsHeight 1.

IEEE StandardsThe S4810–ON complies with the following IEEE standards.• 802.3ab Gigabit Ethernet (1000BASE-T)• 802.3ae 10 Gigabit Ethernet (10GBASE-X)

derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment.WARNING

Korean Package LabelSafety Standards and Compliance Agency Certifications• CUS UL 60950-1, 2nd Edition• CSA 60950-1-03, 2nd Edition• EN 60950-1, 2nd E

Waste Electrical and Electronic Equipment (WEEE) Directive for Recovery, Recycle and Reuse of IT and Telecommunications ProductsDell Networking switch

4. Remove the card.Figure 15. Illustration of removing the SD CardReplacing the Battery on the S4810–ONThe lithium battery is not field replaceable.On

To open the case, follow these steps.1. Remove the small Phillips screws that connect the top of the case to the body. There are three screws evenly s

Installing an AC Power Supply...24Replacing a

Figure 17. Close-Up View of the BatteryBatteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning ba

Figure 18. The European WEEE SymbolFor California:• Perchlorate Material — Special handling may apply.• Refer to http://www.dtsc.ca.gov/hazardouswaste

42

9Technical SupportThis chapter contains the following sections:• The iSupport Website• Contacting the Technical Assistance Center• Requesting a Hardwa

Managing Your CaseLog in to iSupport and select the Service Request tab to view all open cases and Return Materials Authorizations (RMAs).Technical Do

1About this GuideThis guide provides site preparation recommendations, step-by-step procedures for rack mounting and desk mounting, inserting optional

Related DocumentsFor more information about the S4810–ON system, refer to the Dell Networking S4810–Open Networking (ON) Getting Started Guide.NOTE: F

2The S4810–ON SystemThe following sections describe the Dell Networking S4810–ON system.IntroductionThe Dell Networking S4810–ON platform is a next-ge

Figure 2. S4810–ON PSU-Side View1. Mounting Bracket2. Fan Module 13. Fan Module 24. Mounting Bracket5. Power Supply (PSU2)6. Power Supply (PSU1)7. Gro

• Ground cable (not included, optional)• Ground cable screws (included)• Copper/fiber cablesOther optional components are:• Additional power supply un