Dell OptiPlex Gxi Bedienungsanleitung Seite 119
- Seite / 140
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
ISA Configuration Utility Messages B-9
WARNING: Could not
configure Plug and
Play Card Name.
WARNING: Could not
configure PCI device,
ID=DeviceID.
Failed to configure
Number of Total Count
Plug and Play ISA
devices. Use your sys-
tem’s configuration
utility to resolve
conflicts. Press any
key to continue.
The card(s) mentioned are
not fully configured due to
resource conflicts.
If you do not know the allowable resource val-
ues for your Plug and Play or PCI expansion
card, use the following procedure to locate and
resolve the resource conflict:
1. Remove all card configurations from the
ICU.
See “Removing a Card” in Chapter 3 for
instructions.
2. Reboot your system.
The ICU should automatically configure
your Plug and Play or PCI expansion card.
3. Add the ISA expansion cards back into
the ICU, resolving any resource conflicts
as they arise.
See “Adding a Listed Card” in Chapter 3
for instructions.
If your Plug and Play or PCI expansion card is
not automatically configured when you reboot
the system with all other cards removed, you
should contact the manufacturer of the card or
see the chapter titled “Getting Help” in your
Diagnostics and Troubleshooting Guide.
WARNING: Boot Device
conflict detected!
CSN=Card Select Number
Error=Error.
One of the devices is
attempting to use one or
more resources assigned to
the system’s boot device.
Perform the following procedure:
1. Start the ICU.
2. Identify the card marked config err.
This should be the card that is attempting
to use one or more resources required by
the system’s boot device.
3. Follow the procedure for the preceding
error message in this table.
Table B-2. Configuration Manager Messages
(Continued)
Message Probable Cause Corrective Action
NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in the online System User’s Guide.
- OptiPlex 1
- GXi Midsize Systems 1
- Safety Instructions 5
- About This Guide 9
- Warranty and Return Policy 9
- Other Documents You May Need 10
- Notational Conventions 10
- No boot device available 11
- Contents 13
- Chapter 3 14
- Chapter 4 15
- Appendix D 18
- Introduction 25
- System Features 25
- Using the Floor Stand 27
- Energy Star Compliance 28
- Important Note to Windows 95 29
- Accessing Online 29
- • Connecting external devices 30
- • Maintaining the system 30
- • Contacting Dell 30
- 30
- Entering the System Setup 31
- System Setup Screens 32
- System Setup Categories 34
- EIDE Devices 35
- If You Have a Problem 35
- Base Memory 35
- • NONE (the default option) 36
- • 15M - 16M 36
- • ENABLED 36
- • DISABLED BY JUMPER 36
- Boot Sequence 37
- Setup Password 37
- Auto Power On 37
- Power Management 37
- Saving Monitor Power 37
- Serial Port 38
- Assigning a System Password 40
- Your System 41
- Using the Setup Password 42
- Password 43
- Responding to Error Messages 44
- Quick Start 45
- About the ICU 46
- When to Run the ICU 46
- Preparing to Use the ICU 47
- Starting the ICU 47
- Adding a Listed Card 48
- Adding an Unlisted Card 50
- Modifying a Card 51
- RUPT (IRQ) 52
- AVAILABLE 52
- RESOURCES 52
- Viewing Resources 53
- Exiting From the ICU 54
- Advanced Features of the ICU 54
- Resources 55
- Using Integrated Devices 57
- Video Controller 57
- Audio Controller 57
- 4-2 Dell OptiPlex GX 58
- Connecting to a Network 59
- Configuring the NIC 59
- Microsoft Windows NT 3.5 60
- Client Driver 60
- Microsoft Windows 3 61
- MS-DOS Client Driver 61
- Environments 62
- OS/2 Client Driver 62
- Updating NDIS 2.01 Drivers 63
- 4-8 Dell OptiPlex GX 64
- Working Inside Your Computer 65
- Before You Begin 65
- Removing the Computer Cover 66
- Replacing the Computer Cover 67
- Inside Your Computer 68
- Switches 69
- 5-6 Dell OptiPlex GX 70
- 5-8 Dell OptiPlex GX 72
- System Board Labels 74
- 5-12 Dell OptiPlex GX 76
- Removing and Replacing the 77
- 5-14 Dell OptiPlex GX 78
- Chapter 6 79
- Expansion Cards 80
- Adding Memory 82
- Performing a Memory Upgrade 83
- Installing a DIMM 84
- Removing a DIMM 84
- Upgrading the Microprocessor 85
- 6-8 Dell OptiPlex GX 86
- Replacing the System Battery 88
- BATTERY 89
- 6-12 Dell OptiPlex GX 90
- Installing Drives 91
- Removing and Replacing 91
- 7-2 Dell OptiPlex GX 92
- Connecting Drives 93
- 7-4 Dell OptiPlex GX 94
- Installing Drives 7-5 95
- EIDE Drive Addressing 96
- Hard-Disk Drive Bracket 97
- 1.6-inch drive 98
- Installing Drives 7-9 99
- Installing SCSI Devices 100
- Installing Drives 7-11 101
- 7-12 Dell OptiPlex GX 102
- Hard-Disk Drives 103
- 7-14 Dell OptiPlex GX 104
- Technical Specifications 105
- Continued) 107
- ICU Error Messages 111
- • 4 DMA channels 113
- • 7 IRQ lines 113
- • 9 memory address blocks 113
- • 20 I/O ports 113
- • Modify 114
- • You added an ISA 115
- Configuration Manager 116
- (Continued) 117
- Regulatory Notices 121
- FCC Notices (U.S. Only) 121
- IC Notice (Canada Only) 122
- EN 55022 Compliance (Czech 122
- CE Notice 122
- VCCI Notices (Japan Only) 123
- Korean Regulatory Notice 124
- Wymagania Polskiego Centrum 124
- Pozosta³e instrukcje bez 124
- Regulatory Notices C-5 125
- Warranties and Return Policy 127
- Limited Three-Year Warranty 127
- Coverage During Year One 129
- (U.S. and Canada Only) 130
- Printed in the U.S.A 140
- P/N 50577 140
Verwandte Produkte und Handbücher für Computers Dell OptiPlex Gxi
Computers Dell Dimension E521 Bedienungsanleitung
(158 Seiten)
(158 Seiten)
Computers Dell PowerEdge T710 Bedienungsanleitung
(151 Seiten)
(151 Seiten)
Computers Dell XPS 210 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Computers Dell Dimension 8300 Bedienungsanleitung
(146 Seiten)
(146 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.344 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern