Dell OptiPlex Gxi Bedienungsanleitung Seite 98
- Seite / 140
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
7-8 Dell OptiPlex GX
i
Midsize Systems Reference and Installation Guide
5. Slide the drive into the chosen bay of the bracket,
oriented so that the connectors on the back of the
drive will face the back of the chassis—and the
power input connector will be closest to the floor
of the chassis—when the bracket is reinstalled
(see Figure 7-12).
Figure 7-11. Inserting the Hard-Disk Drive in
the Bracket
6. Align the four screw holes of the drive and
bracket. Insert and tighten the screws that came
with your upgrade kit (see Figure 7-11).
If you are replacing a drive in the 1.6-inch slot, use
the four screw holes in the side of the bracket. If you
are replacing a drive in the 1-inch slot, use the four
screw holes in the bottom of the bracket.
7. Reinstall the hard-disk drive bracket in the
chassis.
Hold the bracket by its handle, so that it stays at the
proper tilt. Let it brush the side of the drive cage as
you lower it into the chassis until the two tabs at the
bottom back of the bracket (see Figure 7-11) fit flush
against the front of the rail that extends across the
chassis floor, and the horizontal lip at the back fits
over the rail (see Figure 7-12, which shows the
bracket from the back).
Rotate the bracket down into position, and reinstall
the screw you removed in step 4.
8. Connect one of the device connectors on the EIDE
cable to the 40-pin interface connector on the
back of the hard-disk drive (see Figure 7-12). The
cable is keyed so that the colored edge of the
EIDE cable lines up with the pin-1 end of the
interface connector.
Figure 7-12. Attaching Hard-Disk Drive
Cables
1.6-inch drive
screw (4)
drive bracket
tabs (2)
CAUTION: You must match the colored strip
on the EIDE cable with pin 1 on the IDE1 con-
nector to avoid possible damage to your
system.
EIDE
cable
power input
connector on drive
IDE1 connector
rail
lip
IDE2
connector
DC power cable
interface
connector
- OptiPlex 1
- GXi Midsize Systems 1
- Safety Instructions 5
- About This Guide 9
- Warranty and Return Policy 9
- Other Documents You May Need 10
- Notational Conventions 10
- No boot device available 11
- Contents 13
- Chapter 3 14
- Chapter 4 15
- Appendix D 18
- Introduction 25
- System Features 25
- Using the Floor Stand 27
- Energy Star Compliance 28
- Important Note to Windows 95 29
- Accessing Online 29
- • Connecting external devices 30
- • Maintaining the system 30
- • Contacting Dell 30
- 30
- Entering the System Setup 31
- System Setup Screens 32
- System Setup Categories 34
- EIDE Devices 35
- If You Have a Problem 35
- Base Memory 35
- • NONE (the default option) 36
- • 15M - 16M 36
- • ENABLED 36
- • DISABLED BY JUMPER 36
- Boot Sequence 37
- Setup Password 37
- Auto Power On 37
- Power Management 37
- Saving Monitor Power 37
- Serial Port 38
- Assigning a System Password 40
- Your System 41
- Using the Setup Password 42
- Password 43
- Responding to Error Messages 44
- Quick Start 45
- About the ICU 46
- When to Run the ICU 46
- Preparing to Use the ICU 47
- Starting the ICU 47
- Adding a Listed Card 48
- Adding an Unlisted Card 50
- Modifying a Card 51
- RUPT (IRQ) 52
- AVAILABLE 52
- RESOURCES 52
- Viewing Resources 53
- Exiting From the ICU 54
- Advanced Features of the ICU 54
- Resources 55
- Using Integrated Devices 57
- Video Controller 57
- Audio Controller 57
- 4-2 Dell OptiPlex GX 58
- Connecting to a Network 59
- Configuring the NIC 59
- Microsoft Windows NT 3.5 60
- Client Driver 60
- Microsoft Windows 3 61
- MS-DOS Client Driver 61
- Environments 62
- OS/2 Client Driver 62
- Updating NDIS 2.01 Drivers 63
- 4-8 Dell OptiPlex GX 64
- Working Inside Your Computer 65
- Before You Begin 65
- Removing the Computer Cover 66
- Replacing the Computer Cover 67
- Inside Your Computer 68
- Switches 69
- 5-6 Dell OptiPlex GX 70
- 5-8 Dell OptiPlex GX 72
- System Board Labels 74
- 5-12 Dell OptiPlex GX 76
- Removing and Replacing the 77
- 5-14 Dell OptiPlex GX 78
- Chapter 6 79
- Expansion Cards 80
- Adding Memory 82
- Performing a Memory Upgrade 83
- Installing a DIMM 84
- Removing a DIMM 84
- Upgrading the Microprocessor 85
- 6-8 Dell OptiPlex GX 86
- Replacing the System Battery 88
- BATTERY 89
- 6-12 Dell OptiPlex GX 90
- Installing Drives 91
- Removing and Replacing 91
- 7-2 Dell OptiPlex GX 92
- Connecting Drives 93
- 7-4 Dell OptiPlex GX 94
- Installing Drives 7-5 95
- EIDE Drive Addressing 96
- Hard-Disk Drive Bracket 97
- 1.6-inch drive 98
- Installing Drives 7-9 99
- Installing SCSI Devices 100
- Installing Drives 7-11 101
- 7-12 Dell OptiPlex GX 102
- Hard-Disk Drives 103
- 7-14 Dell OptiPlex GX 104
- Technical Specifications 105
- Continued) 107
- ICU Error Messages 111
- • 4 DMA channels 113
- • 7 IRQ lines 113
- • 9 memory address blocks 113
- • 20 I/O ports 113
- • Modify 114
- • You added an ISA 115
- Configuration Manager 116
- (Continued) 117
- Regulatory Notices 121
- FCC Notices (U.S. Only) 121
- IC Notice (Canada Only) 122
- EN 55022 Compliance (Czech 122
- CE Notice 122
- VCCI Notices (Japan Only) 123
- Korean Regulatory Notice 124
- Wymagania Polskiego Centrum 124
- Pozosta³e instrukcje bez 124
- Regulatory Notices C-5 125
- Warranties and Return Policy 127
- Limited Three-Year Warranty 127
- Coverage During Year One 129
- (U.S. and Canada Only) 130
- Printed in the U.S.A 140
- P/N 50577 140
Verwandte Produkte und Handbücher für Computers Dell OptiPlex Gxi
Computers Dell Dimension E521 Bedienungsanleitung
(158 Seiten)
(158 Seiten)
Computers Dell PowerEdge T710 Bedienungsanleitung
(151 Seiten)
(151 Seiten)
Computers Dell XPS 210 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Computers Dell Dimension 8300 Bedienungsanleitung
(146 Seiten)
(146 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.651 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern