Dell Inspiron 630m Bedienungsanleitung

Dell™ XPS M140Service ManualNotes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer

10 Before You BeginOptical Drive:(1 each – optional)Modem:(1 each)Bluetooth Module:(1 each)Hinge Cover:(2 each)Display Assembly:(4 each)Display Bezel

Before You Begin 11Palm Rest (bottom):(11 each)Fan:(3 each)Speakers:(3 total)System Board (top):(1 each)System Board (bottom):(2 each)

12 Before You Begin

System Components 132System Components NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing t

14 System ComponentsExploded View of the Computer12341056713912118

System Components 151 display assembly 6 optical drive 11 microprocessor thermal-cooling assembly2 hinge cover 7 main battery 12 microprocessor3 keybo

16 System Components

Internal Card With Bluetooth® Wireless Technology 173Internal Card With Bluetooth® Wireless Technology NOTE: If you ordered the optional internal car

18 Internal Card With Bluetooth® Wireless Technology3Remove the M2 x 3-mm screw securing the Bluetooth module and set it aside.1 modem/Mini PCI/wirele

Internal Card With Bluetooth® Wireless Technology 194Lift the Bluetooth module from its compartment.5Grasp the card and gently pull it apart from the

____________________Information in this document is subject to change without notice.© 2005 Dell Inc. All rights reserved.Reproduction in any manner w

20 Internal Card With Bluetooth® Wireless TechnologyReplacing the Bluetooth Module CAUTION: Before you perform any of the procedures in this section,

Hard Drive 214Hard DriveRemoving the Hard Drive CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in

22 Hard Drive NOTICE: When the hard drive is not in the computer, store it in protective, antistatic packaging. See "Protecting Against Electros

Hard Drive 23Replacing the Hard Drive CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Produc

24 Hard Drive1 hard drive (in antistatic bag) 2 foam packaging12

Optical Drive 255Optical DriveAbout the Device Security Screw NOTE: You do not need to install the device security screw unless you want to prevent t

26 Optical Drive3Insert the screwdriver into the indention and push the notch on the metal tab to release the drive from the bay.1 indention 2M2.5 x 8

Optical Drive 274Pull the drive out of the bay.Replacing the Optical Drive CAUTION: Before you perform any of the procedures in this section, follow

28 Optical Drive

Memory Module and Modem 296Memory Module and ModemYour Dell computer comes equipped with two memory slots/connectors labeled DIMM A and DIMM B. DIMM A

31 Before You BeginPreparing to Work Inside the Computer . . . . . . . . . . . . . . . . . . . 7Recommended Tools. . . . . . . . . . . . . . . . . .

30 Memory Module and Modem NOTICE: To prevent damage to the memory module connector, do not use tools of any kind to spread the metal clips that secu

Memory Module and Modem 314Remove the module from the connector at a 45-degree angle.1 memory module 2 metal retention clips (2)12

32 Memory Module and ModemMemory Module DIMM A1Follow the instructions in "Preparing to Work Inside the Computer" on page 7.2Remove the hing

Memory Module and Modem 336Remove the memory module from the connector at a 45-degree angle.1 memory module 2 metal retention clips (2)12

34 Memory Module and ModemReplacing a Memory Module CAUTION: Before you perform any of the procedures in this section, follow the safety instructions

Memory Module and Modem 354Replace the memory module cover and tighten the screws.5Replace the keyboard (see "Replacing the Keyboard" on pag

36 Memory Module and Modem3Disconnect the antenna cables from the Mini PCI card, if applicable. NOTE: The Mini PCI card is optional and may not be in

Memory Module and Modem 374Remove the M2 x 3-mm screw securing the modem to the system board and set it aside.5Pull straight up on the attached pull-t

38 Memory Module and ModemReplacing the Modem CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in th

Memory Module and Modem 396Connect the Mini PCI antenna cables, if applicable.7Replace the modem/Mini PCI/wireless cover and tighten the screws.

4Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Removing the Modem. . . . . . . . . . . . . . . . . . . . . . . . . 35

40 Memory Module and Modem

Hinge Cover 417Hinge CoverRemoving the Hinge Cover CAUTION: Before you perform any of the procedures in this section, follow the safety instructions

42 Hinge CoverReplacing the Hinge Cover CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Prod

Keyboard 438KeyboardRemoving the Keyboard CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Pr

44 Keyboard4Lift the keyboard and hold it up and slightly forward to allow access to the keyboard connector.5Release the latch on the system board con

Keyboard 45Replacing the Keyboard CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product In

46 Keyboard4Slide the six tabs along the front edge of the keyboard beneath the palm rest. NOTE: You may need to push the bottom of the keyboard down

Coin-Cell Battery 479Coin-Cell BatteryRemoving the Coin-Cell Battery CAUTION: Before you perform any of the procedures in this section, follow the sa

48 Coin-Cell BatteryReplacing the Coin-Cell Battery CAUTION: Before you perform any of the procedures in this section, follow the safety instructions

Wireless Mini PCI Card 4910Wireless Mini PCI Card NOTE: If you ordered the optional Mini PCI card at the same time that you ordered your computer, th

5Display Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Removing the Display Latch. . . . . . . . . . . . . . . . . . . . . .

50 Wireless Mini PCI Card3Disconnect the antenna cables from the Mini PCI card. NOTICE: To prevent damage to the Mini PCI card connector, do not use

Wireless Mini PCI Card 515Remove the Mini PCI card from the connector at a 45-degree angle.1 Mini PCI card 2 metal retention clips (2)12

52 Wireless Mini PCI CardReplacing the Mini PCI Card CAUTION: Before you perform any of the procedures in this section, follow the safety instruction

Wireless Mini PCI Card 534Connect the antenna cables to the Mini PCI card. Make certain that the cable connectors snap securely into place.5Replace th

54 Wireless Mini PCI Card

Display Assembly and Display Latch 5511Display Assembly and Display LatchDisplay AssemblyRemoving the Display Assembly CAUTION: Before you perform an

56 Display Assembly and Display LatchReplacing the Display Assembly CAUTION: Before you perform any of the procedures in this section, follow the saf

Display Assembly and Display Latch 577Replace the keyboard (see "Replacing the Keyboard" on page 45).8Replace the hinge cover (see "Rep

58 Display Assembly and Display LatchReplacing the Display Bezel CAUTION: Before you perform any of the procedures in this section, follow the safety

Display Assembly and Display Latch 597Replace the keyboard (see "Replacing the Keyboard" on page 45).8Replace the hinge cover (see "Rep

618 BIOS UpdatesFlashing the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8719 Pin Assignments for I/O ConnectorsUSB Connector . .

60 Display Assembly and Display Latch8Press inward on the metal clamps on both sides of the top flex-cable connector and gently pull to disconnect the

Display Assembly and Display Latch 61Replacing the Display Panel CAUTION: Before you perform any of the procedures in this section, follow the safety

62 Display Assembly and Display Latch9Replace the keyboard (see "Replacing the Keyboard" on page 45).10Replace the hinge cover (see "Re

Display Assembly and Display Latch 63Replacing the Display Latch CAUTION: Before you perform any of the procedures in this section, follow the safety

64 Display Assembly and Display Latch

Palm Rest 6512Palm RestRemoving the Palm Rest CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in th

66 Palm Rest8Remove the eleven M2.5 x 8-mm screws securing the palm rest from the bottom of the computer.1 modem/Mini PCI/wireless cover2 captive scre

Palm Rest 679Turn the computer over and remove the four M2.5 x 5-mm screws securing the top of the palm rest. NOTICE: Release the locking tabs on bot

68 Palm Rest12Moving from left to right, carefully lift the palm rest along the rear edge, near the hinge brackets, then rotate the palmrest forward t

Palm Rest 69Replacing the Palm Rest CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product

Before You Begin 71Before You BeginPreparing to Work Inside the Computer CAUTION: Before you perform any of the procedures in this section, follow th

70 Palm Rest10Replace the display assembly (see "Replacing the Display Assembly" on page 56).11Replace the keyboard (see "Replacing the

Microprocessor Thermal-Cooling Assembly 7113Microprocessor Thermal-Cooling AssemblyRemoving the Microprocessor Thermal-Cooling Assembly CAUTION: Befo

72 Microprocessor Thermal-Cooling AssemblyReplacing the Microprocessor Thermal-Cooling Assembly CAUTION: Before you perform any of the procedures in

Fan 7314FanRemoving the Fan CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Informat

74 FanReplacing the Fan CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information

Microprocessor Module 7515Microprocessor ModuleRemoving the Microprocessor Module CAUTION: Before you perform any of the procedures in this section,

76 Microprocessor Module3Remove the microprocessor thermal-cooling assembly (see "Removing the Microprocessor Thermal-Cooling Assembly" on p

Microprocessor Module 77 NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an un

78 Microprocessor Module

Speakers 7916SpeakersRemoving the Speakers CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the P

8 Before You Begin8Slide and hold the battery bay latch release on the bottom of the computer, then pull the battery out of the battery bay.Recommende

80 SpeakersReplacing the Speakers CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product In

Speakers 819Replace the keyboard (see "Replacing the Keyboard" on page 45).10Replace the hinge cover (see "Replacing the Hinge Cover&qu

82 Speakers

System Board 8317System BoardRemoving the System Board CAUTION: Before you perform any of the procedures in this section, follow the safety instructi

84 System Board16Turn the computer over so that the bottom is facing down and remove the M2.5 x 5-mm screw securing the system board.17Disconnect the

System Board 8520With the rear of the computer facing you, gently lift the system board assembly from the left side, then slide the system board assem

86 System BoardReplacing the System Board CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Pr

BIOS Updates 8718BIOS UpdatesFlashing the BIOS NOTICE: Plug the AC adapter into a known-good power source to prevent a loss of power. Failure to do s

88 BIOS Updates

Pin Assignments for I/O Connectors 8919Pin Assignments for I/O ConnectorsUSB ConnectorVideo ConnectorPin Signal1 USB5V+2 USBP–3 USBP+4 GND

Before You Begin 9Computer OrientationScrew IdentificationThe following chart provides the number of screws used to secure the various system componen

90 Pin Assignments for I/O ConnectorsS-Video TV-Out ConnectorPin Signal Pin Signal1 CRT_R 9 5V+2 CRT_G 10 GND3 CRT_B 11 MONITOR_DETECT–4 NC 12 DDC_DAT

Pin Assignments for I/O Connectors 91IEEE 1394 ConnectorPin Signal1 TPB–2 TPB+3 TPA–4 TPA+

92 Pin Assignments for I/O Connectors