Dell TL2000 Bedienungsanleitung Seite 129
- Seite / 264
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
v Internal Label - Encrypt All: Check your tape backup software application
documentation to see if this feature is supported.
10.
A primary and secondary EKM server can be set for each logical library. Each
partition has its own Encryption and EKM settings. Maintaining primary and
secondary EKM servers is desired for maximum availability of encrypted
backup and recovery. These settings are required for Library Managed
Encryption only. Enter the EKM Server Setting information.
v Primary IP address (IPv4 or IPv6): Enter the IP address of the primary
EKM server.
v Primary TCP port: After entering the Primary IP address, the library will
automatically set the value of the Primary TCP port.
v Secondary IP address (IPv4 or IPv6): Enter the IP address of the secondary
EKM server.
v Secondary TCP port: After entering the Secondary IP address, the library
will automatically set the value of the Secondary TCP port.
Note:
The Default Port for TCP (SSL disabled) is 3801. The Default Port for
SSL is 443. These values are the default values set by the library.
They can be changed depending on the user configuration but the
user has to make sure they match the EKM properties file.
Note:
If SSL is enabled the encryption host configuration will request a SSL
port instead of a TCP port. Review the Dell PowerVault Encryption Key
Manager User’s Guide for instructions to locate the appropriate port
settings.
11.
Click Activate to apply the changes.
12. Install the Dell Encryption Key Manager (EKM) application on your host.
Refer to the Dell EKM documentation provided with your Encryption packet.
The EKM IP address and EKM port will be provided to the user by the EKM
application.
Configure Library: Drives
This page allows you to modify the current ID assigned to a SCSI or Fibre Channel
drive. This page allows any drive in the library to be powered off by de-selecting
the check mark in the Power On box. The displayed information will vary
depending on the library model and drive type (SCSI, SAS, or Fibre Channel).
Table 5-11 lists all available elements on this page. An ″X″ indicates that the
element displays for the specified drive type.
Table 5-11. Drive Identity page elements
Menu Item Description 2U Library 4U Library
SCSI Fibre SAS SCSI Fibre SAS
SCSI ID For each SCSI drive, click on the drop down list
and select the number of the slot in which the
drive is located.
X X
Power On For each drive, click in the box to power ON the
selected drive.
X X X X X X
Control Path The control path drive communicates messages
from the host to the library. Select this option for
each drive that you want to be a control path
drive. At least one drive in each logical library
must be designated as a control path drive.
X X X X X X
Port A Configuration:
Chapter 5. Operations 5-43
- User’s Guide 1
- Read this First 5
- Contents 7
- Figures 9
- Danger Notice 13
- Caution Notice 13
- Class I Laser Product 14
- Rack Safety 15
- Preface 17
- Front Panel 19
- Rear Panel 21
- Internal View of Library 23
- Bar Code Reader 24
- Encryption 24
- SNMP Messaging 26
- Ultrium Tape Drives 27
- Speed Matching 28
- Channel Calibration 28
- Power Management 29
- Library Specifications 29
- Operation Specifications 30
- Environmental Specifications 30
- Product Environment 31
- Supported Device Drivers 31
- Operator Control Panel 33
- Power-ON Display 34
- Input Modes 35
- Power ON/OFF 36
- Web User Interface 36
- System Status 38
- Basic Guidelines 41
- Library Sharing 41
- Host Interfaces 46
- SCSI Interface 46
- Using Multiple SCSI Buses 47
- SAS Interface 48
- Fibre Channel Interface 48
- Cables and Speeds 49
- Installing Your Library 51
- Choosing a Location 51
- Unpacking the Library 52
- Verifying the Shipment 52
- 2. Store the lock ( 55
- ) and label ( 55
- Figure 4-5 on page 4-6 55
- Connecting a Power Cord 63
- Configuring Your Library 64
- Verifying/Updating Firmware 67
- Setting Up Encryption 71
- Interface 77
- Configuration 78
- Preparing the Host 79
- Verifying the Connection 79
- Cartridge Magazines 80
- 2U Library I/O Station 81
- 4U Library I/O Station 82
- Chapter 5. Operations 87
- Chapter 5. Operations 5-3 89
- Chapter 5. Operations 5-5 91
- Chapter 5. Operations 5-7 93
- Chapter 5. Operations 5-9 95
- Monitor Menu 97
- Monitor: Drive 99
- Monitor: Inventory 101
- Control Menu 102
- Control: Move Cartridges 103
- Control: Magazine 103
- Configure Menu 104
- Chapter 5. Operations 5-19 105
- Configure: Library 106
- Chapter 5. Operations 5-21 107
- Configure: Drive 108
- Configure: Network 109
- Configure: Set Access PIN 110
- Chapter 5. Operations 5-25 111
- Service Menu 112
- Service: Run Tests 113
- Service: Service (Drives) 113
- Drive Tests 114
- Clean Drive 114
- Drive Power 114
- Web User Interface Menus 115
- Monitor Library Menu 116
- Chapter 5. Operations 5-31 117
- Chapter 5. Operations 5-33 119
- Chapter 5. Operations 5-35 121
- Drive Inventory 123
- Magazine Inventory 123
- Configure Library Menu 124
- Chapter 5. Operations 5-39 125
- Chapter 5. Operations 5-41 127
- Configure Library: Drives 129
- Configure Library: Network 130
- Chapter 5. Operations 5-45 131
- Chapter 5. Operations 5-47 133
- Manage Library Menu 135
- Service Library Menu 136
- View Logs 137
- View Drive Logs 137
- Save Drive Dump 138
- Chapter 5. Operations 5-53 139
- Service Library: Reboot 141
- Import Media 141
- Export Media 142
- Dedicated Cleaning Slot 143
- Reserving Slots 143
- Data Cartridges 145
- Cartridge Compatibility 146
- WORM Media 147
- WORM Media Errors 147
- Cleaning Cartridge 147
- Bar Code Label 148
- Write-Protect Switch 149
- Handling the Cartridges 150
- Provide Training 150
- Ensure Proper Packaging 150
- Chapter 7. Troubleshooting 155
- Maintenance Problems 156
- Problem 165
- Chapter 8. Error Codes 169
- Tools Required 187
- Electrostatic Discharge 187
- Relocating Your Library 187
- 1 SCSI cable 190
- 2U Library 4U Library 193
- Swapping Power Supplies 208
- Enclosure 211
- Mixing of Drives 215
- SCSI Element Addressing 217
- Appendix C. Sense Data 225
- 30h 07h Cleaning failure 226
- Drive Sense Data 230
- Red Hat Enterprise Linux 240
- 2003/XP and 2008/Vista 243
- Windows 2008/Vista 244
- Notices 247
- Glossary 249
- Numbers 249
- Glossary H-3 251
- Glossary H-5 253
- Glossary H-7 255
- Glossary H-9 257
- Printed in USA 264
Verwandte Produkte und Handbücher für Computerzubehör Dell TL2000
Computerzubehör Dell 5316M Bedienungsanleitung
(15 Seiten)
(15 Seiten)
(268 Seiten)
(330 Seiten)
(32 Seiten)
(178 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.109 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern