Dell OptiPlex GX400 Bedienungsanleitung Seite 25
- Seite / 88
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
15. Enter system setup, and update the drive settings.
After you update the system settings, exit system setup and reboot the computer.
16. Partition and logically format the drive before proceeding to the next step.
See the operating system's documentation for instructions.
17. Run the Dell Diagnostics to test the drive.
18. If the hard drive you installed is the primary drive, install the operating system on the drive.
See the operating system's documentation for instructions.
EIDE Device Installation Guidelines
Jumper Settings
All EIDE drives should be configured for the Cable Select jumper position, which assigns master and slave status to drives by their position on the interface
cable. When two EIDE drives are connected to a single EIDE interface cable and are configured for the Cable Select jumper position, the drive attached to the
last connector on the interface cable is the master, or boot device (drive 0), and the device attached to the middle connector on the interface cable is the slave
device (drive 1). Refer to the documentation in your drive upgrade kit for information on setting devices to the Cable Select jumper position.
General Guidelines
With the two EIDE interface connectors on the input/output (I/O) board, your system can support up to four EIDE drives:
l The primary EIDE connector, labeled "IDE PRI," should be cabled to EIDE hard drives
l The secondary EIDE connector, labeled "IDE SEC," should be cabled to EIDE CD, DVD, tape, SuperDisk, and Zip drives
To locate the EIDE interface connectors on the system board, see "System Board Components." Each EIDE interface connector on the I/O board supports the
following:
l Two channels, master and slave
l Logical block addressing (LBA)
l Programmed I/O (PIO) Mode 3 and Mode 4
l Ultra Advanced Technology Attachment (ATA)/100, ATA/66, or ATA/33
EIDE Cables
Ultra ATA/66 and ATA/100 hard drives require an 80-conductor cable to transfer data at full speed. The 80-conductor cable has a 40-pin connector like the
ATA/33 cable, but it has twice as many wires within the cable. If you use an ATA/33 cable with Ultra ATA/100 hard drives, the drives will operate properly, but
data will transfer at ATA/33 speeds.
SCSI Device Installation Guidelines
This section describes how to configure and install SCSI devices in your system. To install a SCSI device, you must have a SCSI controller card installed in your
system.
SCSI ID Numbers
Internal SCSI devices must have a unique SCSI ID number from 0 to 15.
When SCSI devices are shipped from Dell, the default SCSI ID numbers for the primary and secondary controllers are assigned as follows:
l SCSI controller: SCSI ID 7
l Boot SCSI hard drive: SCSI ID 0
l SCSI CD drive: SCSI ID 5
l SCSI tape or digital audio tape (DAT) drive: SCSI ID 6
SCSI devices installed by Dell are configured correctly during the manufacturing process. You do not need to set the SCSI ID for these SCSI devices.
If you attach additional optional SCSI devices, refer to the documentation for each device for information about setting the appropriate SCSI ID number.
Device Termination
NOTE: A SuperDisk drive is typically installed as the master device on the secondary EIDE system-board connector.
NOTICE: DellrecommendsthatyouuseonlyEIDEcablespurchasedfromDell.CablespurchasedelsewherearenotguaranteedtoworkwithDell™
systems.
NOTE: There is no requirement that SCSI ID numbers be assigned sequentially or that devices be attached to the cable in order by ID number.
NOTICE: Dell recommends that you use only SCSI cables purchased from Dell. Cables purchased elsewhere are not guaranteed to work with Dell
systems.
- Notes, Notices, and Cautions 1
- About Your Computer 2
- Back View of Your Computer 3
- Inside Your Computer 4
- System Board Components 5
- Advanced Features 6
- Manageability 7
- Security 8
- Password Protection 9
- Setup Password 10
- Jumper Settings 11
- Installing a TAPI Device 12
- Power Management 13
- Installing Upgrades 15
- Power Supply 17
- Front Panel 17
- System Memory 18
- Upgrading System Memory 19
- Removing a Memory Module 19
- Disk Drives and Media 20
- General Guidelines 25
- EIDE Cables 25
- SCSI ID Numbers 25
- Device Termination 25
- AGP Card Brace 26
- Expansion Cards 26
- Removing the Filler Bracket 27
- Microprocessor 29
- Removing the Microprocessor 31
- Removing the VRM 32
- Replacing the VRM 32
- System Battery 33
- Back to Contents Page 34
- Technical Specifications 35
- Solving Problems 38
- Monitor Problems 39
- Video Problems 39
- Sound and Speaker Problems 40
- Printer Problems 41
- Mouse Problems 43
- Keyboard Problems 43
- Diskette Drive Problems 44
- Hard Drive Problems 45
- Battery Problems 47
- Expansion-Card Problems 47
- Repairing a Wet Computer 48
- Hardware Conflicts 49
- System Memory Problems 50
- Microprocessor Problems 50
- System Board Problems 51
- Dell Diagnostics 52
- Advanced Testing 53
- Messages and Codes 54
- System Beep Codes 56
- Warning Messages 57
- Diagnostics Messages 57
- Diagnostic Indicators 57
- Back-Panel Indicators 58
- Software Problems 59
- BIOS Recovery Utility 61
- Getting Help 62
- Problems With Your Order 63
- Product Information 63
- Before You Call 63
- Dell Contact Numbers 64
- Additional Information 71
- IC Notice (Canada Only) 72
- CE Notice (European Union) 72
- Battery Disposal 72
- VCCI Notice (Japan Only) 73
- MIC Class A Regulatory Mark 74
- Class B Device 74
- MIC Class B Regulatory Mark 74
- BSMI Notice (Taiwan Only) 75
- ENERGY STAR®Compliance 76
- Coverage During Year One 77
- General Provisions 77
- Safety Instructions 80
- Overview 82
- New User Interface 82
- Clean Desktop Wizard 83
- Taskbar Grouping 83
- Notification Area Cleanup 83
- System Restore 84
- Restore Process 85
- Driver Rollback 85
- How to Add Users 86
- Internet Connection Firewall 87
Verwandte Produkte und Handbücher für Computers Dell OptiPlex GX400
(2 Seiten)
Computers Dell OptiPlex GX260 Bedienungsanleitung
(100 Seiten)
(100 Seiten)
Computers Dell Precision 450 Bedienungsanleitung
(158 Seiten)
(158 Seiten)
Computers Dell Precision 650 Bedienungsanleitung
(155 Seiten)
(155 Seiten)
(2 Seiten)
Computers Dell Precision 350 Bedienungsanleitung
(40 Seiten)
(40 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern