Dell PowerEdge VRTX Bedienungsanleitung Seite 331
- Seite / 832
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
802.1X Commands 331
FILE LOCATION: C:\Users\gina\Desktop\Checkout_new\CLI Folders\Dell Plasma-ARC
2+3\new_system_mifs_ARC2_latest\802_1X.fm
DELL CONFIDENTIAL – PRELIMINARY 4/3/14 - FOR PROOF ONLY
dot1x guest-vlan timeout
Use the dot1x guest-vlan timeout Global Configuration mode command to
set the time delay between enabling 802.1X (or port up) and adding a port to
the guest VLAN. Use the no form of this command to restore the default
configuration.
Syntax
dot1x guest-vlan timeout
timeout
no dot1x guest-vlan timeout
Parameters
•
timeout
—Specifies the time delay in seconds between enabling 802.1X (or
port up) and adding the port to the guest VLAN. (Range: 30–180).
Default Configuration
The guest VLAN is applied immediately.
Command Mode
Global Configuration mode
User Guidelines
This command is relevant if the guest VLAN is enabled on the port.
Configuring the timeout adds a delay from enabling 802.1X (or port up) to
the time the device adds the port to the guest VLAN.
Example
The following example sets the delay between enabling 802.1X and adding a
port to a guest VLAN to 60 seconds.
console(config)#
dot1x guest-vlan timeout
60
- PowerEdge VRTX 1Gb Switch 1
- Module — R1-2401 1
- CLI Reference Guide 1
- Notes, Cautions, and Warnings 2
- Contents 3
- User (Privilege) Levels 33
- CLI Command Modes 35
- Global Configuration Mode 36
- Interface Configuration Modes 36
- Starting the CLI 37
- Privileged EXEC 38
- CLI Command Conventions 39
- Port Naming Convention 40
- Interface List 41
- Entering Commands 42
- Command Completion 43
- Keyboard Shortcuts 43
- IPv6 Address Conventions 44
- Preface 45 45
- 46 Preface 46
- User Interface Commands 47
- User Interface Commands 51 51
- User Interface Commands 55 55
- User Interface Commands 59 59
- 72 User Interface Commands 72
- Macro Commands 73
- Macro Commands 79 79
- macro-name 80
- [parameter -name3 value 80
- 84 Macro Commands 84
- 86 Macro Commands 86
- Example 2 - Ping a site 89
- 92 System Management Commands 92
- 96 System Management Commands 96
- System Management Commands 99 99
- System Management Commands 100
- Command Mode 110
- User EXEC mode 112
- User Guidelines 113
- Parameters 113
- Default Usage 113
- 2365491870 115
- Clock Commands 117
- *10:46:48 UTC May 28 2013 118
- Time source is sntp 118
- Clock Commands 119 119
- abc +2 minutes 32 119
- Default Configuration 120
- Clock Commands 125 125
- Clock Commands 127 127
- Clock Commands 129 129
- 192.1.1.1 130
- Clock Commands 131 131
- source-interface 131
- vlan 10 131
- source-interface-ipv6 132
- Clock Commands 133 133
- Time zone (Static): 134
- Summertime (DHCPv4 on VLAN1): 134
- Summertime (Static): 135
- 135
- Privileged EXEC mode 137
- 138 Clock Commands 138
- Commands 139
- Examples 143
- URL of the FLASH file 144
- Startup configuration file 144
- Auto-Update and Auto 153
- Configuration 153
- Management ACL Commands 161
- 168 Management ACL Commands 168
- SNMP Commands 169
- {included 176
- 184 SNMP Commands 184
- 2c 187
- SNMP Commands 191 191
- 11:AB:01:CD:23:44 191
- SNMP Commands 193 193
- SNMP Commands 195 195
- New_York 195
- sysName sysname TechSupp 196
- 198 SNMP Commands 198
- 200 SNMP Commands 200
- RSA and Certificate Commands 201
- Lists of Commands 202
- Web Server Commands 217
- idle-seconds 218
- Web Server Commands 219 219
- Web Server Commands 223 223
- Global Configuration mode 223
- 224 Web Server Commands 224
- Login Commands 225
- [row key-string 232
- Username Fingerprint 235
- Line Commands 237
- Line Commands 239 239
- 240
- 242 Line Commands 242
- Accounting 243
- 245
- [method2...] 246
- 246
- 248
- encrypted-password 252
- RADIUS Commands 275
- RADIUS Commands 279 279
- vlan 100 279
- RADIUS Commands 281 281
- 284 RADIUS Commands 284
- TACACS+ Commands 285
- TACACS+ Commands 287 287
- enterprise 287
- TACACS+ Commands 289 289
- 292 TACACS+ Commands 292
- SYSLOG Commands 293
- facility 294
- SYSLOG Commands 297 297
- SYSLOG Commands 299 299
- {copy 300
- SYSLOG Commands 301 301
- 306 SYSLOG Commands 306
- Remote Network Monitoring 307
- (RMON) Commands 307
- [interval seconds] 309
- [interface-id] 310
- {history 322
- 802.1X Commands 325
- 802.1X Commands 331 331
- 802.1X Commands 333 333
- 802.1X Commands 343 343
- 802.1X Commands 349 349
- interface-id 351
- 352 802.1X Commands 352
- 802.1X Commands 355 355
- 356 802.1X Commands 356
- users for the device 356
- 358 802.1X Commands 358
- interface-id 359
- gi0/1-4 360
- {10 363
- {half 364
- {auto 366
- {on 367
- {interface-id} 370
- [interface-id 370
- PHY Diagnostics Commands 383
- [interface interface-id 384
- 386 PHY Diagnostics Commands 386
- EEE is enabled 387
- 392 EEE Commands 392
- 394 EEE Commands 394
- LLDP are running on the port 394
- EEE Commands 395 395
- Remote Rx Timer: 5 usec 395
- Resolved Timer: 25 usec 395
- Local Rx Timer: 20 usec 395
- Remote Tx Timer: 25 usec 395
- 396 EEE Commands 396
- Green Ethernet 397
- Green Ethernet 399 399
- 404 Green Ethernet 404
- Port Channel Commands 405
- {src-dst-mac 406
- 406
- 408 Port Channel Commands 408
- Address Table Commands 409
- bridge multicast mode 410
- Address Table Commands 415 415
- port-channel-list 416
- {ethernet interface-list 422
- {forwarding 427
- interface-list 429
- Examples: 433
- seconds 434
- Example 441
- [vlan vlan-id 442
- [vlan vlan-id] 442
- 448 Address Table Commands 448
- [interface-id] 449
- Port Monitor Commands 453
- 456 Port Monitor Commands 456
- LLDP Commands 457
- LLDP Commands 460
- {enable 463
- LLDP Commands 467 467
- {enable 468
- {add 472
- {mac-address 474
- 476 LLDP Commands 476
- 484 LLDP Commands 484
- 486 LLDP Commands 486
- 488 LLDP Commands 488
- 490 LLDP Commands 490
- Spanning-Tree Commands 491
- Spanning-Tree Commands 493 493
- Spanning-Tree Commands 495 495
- {point-to-point 499
- {long 500
- {filtering 501
- {filtering 502
- [interface interface-id] 505
- Spanning-Tree Commands 507 507
- {current 512
- [interface-id] [ 515
- instance-id] 515
- 516 Spanning-Tree Commands 516
- 518 Spanning-Tree Commands 518
- 520 Spanning-Tree Commands 520
- 522 Spanning-Tree Commands 522
- 524 Spanning-Tree Commands 524
- 526 Spanning-Tree Commands 526
- Path Cost 527
- Root Port 527
- 528 Spanning-Tree Commands 528
- 532 Spanning-Tree Commands 532
- VLAN Commands 533
- vlan-id 535
- vlan-name 535
- 536 VLAN Commands 536
- VLAN (VLAN 1): 536
- 221-228, vlan 889 538
- vlan-list 545
- Interface-id 560
- 572 VLAN Commands 572
- Voice VLAN Commands 573
- {src 576
- [remark] 577
- 582 Voice VLAN Commands 582
- IGMP Snooping Commands 583
- IGMP Snooping Commands 587 587
- IGMP Snooping Commands 589 589
- TV VLANs 599
- 600 IGMP Snooping Commands 600
- IGMP Commands 601
- IGMP Commands 603 603
- IGMP Commands 605 605
- 606 IGMP Commands 606
- [port_channel_number] 611
- DHCP Snooping Commands 623
- DHCP Snooping Commands 627 627
- DHCP Snooping Commands 633 633
- 0060.704C.73FF 23 633
- 176.10.1.1 gi0/4 633
- DHCP Snooping Commands 635 635
- 644 DHCP Snooping Commands 644
- DHCP Relay Commands 645
- DHCP Relay Commands 647 647
- 176.16.1.1 647
- DHCP Relay Commands 651 651
- 652 DHCP Relay Commands 652
- DHCPv6 Commands 653
- DHCPv6 Commands 655 655
- 662 DHCPv6 Commands 662
- IP Addressing Commands 667 667
- IP Addressing Commands 668
- 192.168.1.1 668
- IP Addressing Commands 671 671
- ip-address 672
- ARP timeout: 80000 Seconds 673
- 678 IP Addressing Commands 678
- IPv6 Commands 679
- 2001:0DB8::45A vlan1 690
- 0002.7D1A.9472 690
- IPv6 Commands 697 697
- tunnel 1 697
- IPv6 Commands 699 699
- 706 IPv6 Commands 706
- IPv6 Tunnel Commands 707
- IPv6 Tunnel Commands 709 709
- 712
- 714 IPv6 Tunnel Commands 714
- ACL Commands 723
- ACL Commands 724
- time-range 727
- [acl-name] 731
- ACL Commands 737 737
- list-of-flags 738
- acl-name 739
- ACL Commands 751 751
- 756 ACL Commands 756
- [exceed-action {drop 768
- 6 6 6 6 6 6 6 6 776
- committed-burst-bytes 779
- {cos 789
- policer1 797
- DNS Client Commands 801
- DNS Client Commands 803 803
- website.com 803
- DNS Client Commands 805 805
- server1-address 808
- 810 DNS Client Commands 810
- MLD Snooping Commands 811
- MLD Snooping Commands 819 819
- MLD Commands 825
- MLD Commands 827 827
- MLD Commands 829 829
- 830 MLD Commands 830
- Port Features 831
- 832 Port Features 832
Verwandte Produkte und Handbücher für Computerhardware Dell PowerEdge VRTX
Computerhardware Dell AX4-5 Bedienungsanleitung
(72 Seiten)
(72 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.905 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern