Dell Force10 E300 Schnellstart Benutzerhandbuch Seite 1

Dell Force10E300, E600i, and E1200iSystemsQuick Start GuideRegulatory Model: E300/E600i TeraScale/E600i ExaScale/E1200i TeraScale/E1200i ExaScale

8 Installing the HardwareE300 DC PEM Chassis GroundE600i TeraScale and ExaScale DC Chassis GroundStep Task1 Locate the chassis ground connector studs

Installing the Hardware 93 Attach the grounding cable onto the ground studs. The grounding cable must comply with your local electrical codes in size

10 Installing the HardwareE1200i TeraScale and ExaScale AC Chassis GroundE1200i TeraScale and ExaScale DC Chassis GroundStep Task1 Locate the chassis

Installing the Hardware 11Installing Power ModulesThis section provides instructions to install AC Power Supply Units (PSUs) and DC Power Entry Module

12 Installing the Hardware WARNING: Electrostatic discharge (ESD) damage can occur when components are mishandled. Always wear an ESD-preventive wris

Installing the Hardware 13 NOTE: Power modules are not field serviceable.E300 DC Power ModulesThe E300 supports a minimum of one DC PEM. You must hav

14 Installing the Hardware NOTE: Please take precautions against over-tightening the screws or nuts on this device.Installing a DC PEMStep Task1 Turn

Installing the Hardware 15E600i AC Power ModulesThe E600i requires a minimum of two AC Power Supplies.The chassis has four power supply slots. You may

16 Installing the HardwareE600i DC Power ModulesThe system requires a minimum of one load-sharing PEM to operate, but two are recommended for redundan

Installing the Hardware 17E1200i AC Power ModulesWhen installing the AC power supplies in the E1200i system, make note of the following:• E1200i ExaSc

18 Installing the Hardware WARNING: Leakage Current (High Touch Current) in AC-powered systems: AC power cords are secured to the power inlet using t

Installing the Hardware 19 WARNING: An external disconnect shall be provided and shall be easily accessible. Dell Force10 recommends that you use a 1

20 Installing the HardwareInstalling RPMs, Line Cards, and SFMsUnpacking Cards WARNING: Electrostatic discharge (ESD) damage can occur when component

Installing the Hardware 21Installing the RPMs and Line Cards CAUTION: Use of controls or adjustments or performance of procedures other than those sp

22 Installing the HardwareE600iRPMsThe E300 system requires the installation of at least one RPM, although two are recommended for redundancy. RPMs ar

Installing the Hardware 23E1200iRPMsThe E1200i system requires the installation of at least one RPM, although two are recommended for redundancy. • Do

24 Installing the HardwarePreparing and Installing RPMs and Line CardsTo prolong the life of the EMI seals, begin installing cards in the right-most s

Installing the Hardware 25Power Up Sequence WARNING: Make sure that the switch on the remote power source is in the OFF position until you are ready

26 Installing the HardwareSupplying PowerTo turn the power off on the power modules, use one of the following methods:• On the DC PEMs, flip the switc

Installing the Hardware 27monitor. When the boot process is complete, the card LEDs remain online (green) and the console monitor displays the Command

Dell Force10E300, E600i, and E1200iSystemsQuick Start GuideRegulatory Model: E300/E600i TeraScale/E600i ExaScale/E1200i TeraScale/E1200i ExaScale

28 Installing the HardwareE300 SpecificationsE300 Chassis Physical DesignE300 Environmental ParametersParameter E1200i AC SpecificationsHeight 14 inch

Installing the Hardware 29E300 AC Power Supplies Power RequirementsE300 DC PEM Power RequirementsE300 Module Power RequirementsE600i SpecificationsE60

30 Installing the HardwareE600i TeraScale Environmental ParametersE600i TeraScale AC Power Supply Unit RequirementsWidth 17.4 inches (44.2 cm)Depth (w

Installing the Hardware 31E600i ExaScale Chassis Physical DesignMaximum AC Power Supply Input 16 A @ 100 VAC per module12 A @ 200 VAC per moduleMaximu

32 Installing the HardwareE600i ExaScale Environmental ParametersE600i ExaScale AC Power Supply Unit RequirementsMaximum for fully loaded chassis 120

Installing the Hardware 33E1200i SpecificationsE1200i TeraScale Chassis Physical DesignE1200i TeraScale Environmental ParametersMaximum Power Consumpt

34 Installing the HardwareE1200i TeraScale Power RequirementsE1200i ExaScale Chassis Physical DesignVibration Designed to meet Telcordia GR-63 CORENon

Installing the Hardware 35E1200i ExaScale Environmental ParametersE1200i ExaScale Power RequirementsWeight fully loaded (backplane, air filter, 2 fan

36 Installing the HardwareMaximum Thermal Output19,449 BTU/hour (5,700 W) 17,402 BTU/hour (5,100 W)Maximum Input Current (per power supply)15.0 A @ 20

Installing the Software 372Installing the SoftwareNavigating CLI ModesThe FTOS prompt changes to indicate the CLI mode. You must move linearly through

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indic

38 Installing the SoftwareAccessing the Console with a DB-9 AdapterYou can connect to the console using a RJ-45 to RJ-45 rollover cable and a RJ-45 to

Installing the Software 39Accessing the Console with a DB-25 AdapterYou can connect to the console using an RJ-45 to RJ-45 rollover cable and RJ-45 to

40 Installing the SoftwareConfigure Layer 2 (Data Link) ModeUse the switchport command in INTERFACE mode to enable Layer 2 data transmissions through

Installing the Software 41Configure the Management Port IP AddressAssign IP addresses to the management ports in order to access the system remotely.

42 Installing the SoftwareConfigure the Enable PasswordThe EXEC Privilege mode is accessed by the enable command. Configure a password as a basic secu

Installing the Software 43When an interface is configured, a switchport automatically places it in the Default VLAN as an untagged interface. All swit

44 Installing the SoftwareAssign an IP Address to a VLAN NOTE: An IP address cannot be assigned to the Default VLAN, which, by default, is VLAN 1. To

Installing the Software 45

46 Installing the Software

About this Guide 3About this GuideThis document is intended as a Quick Start Guide to get new systems up and running and ready for configuration. For

www.dell.com | support.dell.comPrinted in the U.S.A.

4 About this Guide

Installing the Hardware 51Installing the HardwareThis guide assumes all site preparation has been performed before installing the chassis. Installing

6 Installing the HardwareInstalling the Chassis in a Two-Post Rack3 Attach the bar to the equipment rack brackets using the mounting screws provided b

Installing the Hardware 7Installing E300 Chassis into RackInstalling E600i and 1200i into RackAttach a Ground Cable to the Chassis NOTE: The rack ins