Dell DCL and 3 Betriebsanweisung Seite 124
- Seite / 254
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
122 PERC 3/DC or PERC 3/DCL Hardware Installation
www.dell.com | support.dell.com
J2, and J3 Termination Enable
J2, and J3 are 3-pin connectors that set the SCSI termination for each SCSI
channel. The default is OPEN. Table 9-2 displays the termination enable
settings.
J9 Onboard BIOS Enable
J9 is a 2-pin connector that enables or disables the PERC 3/DC or PERC
3/DCL onboard BIOS. The onboard BIOS should be enabled (J9
unjumpered) for normal board operation. Unjumpered is the default. Table
9-3 displays the settings for J9.
J13 Dirty cache (Write Pending) LED 2-pin header
J14 SCSI activity LED 4-pin header
J15 Channel 1 external Wide SCSI 68-pin connector
J16 Channel 0 TERMPWR enable 2-pin header
J17 I2C connector 4-pin header
J18 Channel 1 TERMPWR enable 2-pin header
Table 9-2. J2 and J3 Termination Enable Settings
Jumper SCSI
Channel
SCSI
Termination
Controlled by
Software
SCSI
Termination
Always
Disabled
SCSI
Termination
Always
Enabled
J2 0 Short pins 1-2 Short pins 2-3 OPEN
(default)
J3 1 Short pins 1-2 Short pins 2-3 OPEN
(default)
Table 9-3. J9 Onboard BIOS Enable Settings
J9 Setting Onboard BIOS Status
Unjumpered Enabled (default)
Jumpered Disabled
Table 9-1. Jumper Settings
(continued)
Connector Description Type
- PERC 3 User’s Guide 1
- ____________________ 2
- Safety Instructions 3
- When Using Your Computer 4
- Ergonomic Computing Habits 7
- Battery Disposal 7
- Contents 9
- 3 RAID Levels 10
- 4 PERC 3/SC Features 10
- 6 PERC 3/QC Features 12
- 7 Configuring PERC 3 12
- 12 Dell Manager 16
- 13 Troubleshooting 17
- 16 Contents 18
- 18 Figures 20
- PERC 3 Overview 26
- PERC 3 Features 26
- SCSI Channels 27
- SCSI Connectors 27
- Operating System Support 29
- 28 Overview 30
- Introduction to RAID 31
- RAID Definition 32
- Components and Features 33
- Consistency Check 34
- Disk Striping 34
- Stripe Width 35
- Stripe Size 35
- Disk Mirroring 36
- Disk Spanning 37
- Hot Spares 39
- Disk Rebuilds 40
- Hot Swap 41
- SCSI Drive States 41
- Logical Drive States 42
- Enclosure Management 42
- RAID Levels 43
- Selecting a RAID Level 44
- 44 RAID Levels 46
- Figure 3-1. RAID 0 Array 46
- 46 RAID Levels 48
- Figure 3-2. RAID 1 Array 48
- 48 RAID Levels 50
- Figure 3-3. RAID 5 Array 50
- 50 RAID Levels 52
- Figure 3-4. RAID 10 Array 52
- 52 RAID Levels 54
- Figure 3-5. RAID 50 Array 54
- PERC 3/SC Features 55
- Hardware Requirements 56
- Configuration Features 56
- SMART Technology 57
- Array Performance Features 58
- Software Utilities 59
- PERC 3/SC Specifications 60
- PCI Bridge/CPU 61
- Cache Memory 61
- 60 PERC 3/SC Features 62
- SCSI Firmware 63
- RAID Management 63
- PERC 3/DC and PERC 65
- 3/DCL Features 65
- Configuration on Disk 67
- Fault Tolerance Features 69
- PERC 3/DC and PERC 3/DCL 70
- Specifications 70
- PERC 3/DC and PERC 3/DCL BIOS 72
- Onboard Speaker 72
- Serial Port 72
- SCSI Bus 72
- PERC 3/QC Features 75
- PERC 3/QC Specifications 80
- 80 PERC 3/QC Features 82
- Configuring PERC 3 85
- Current Configuration 86
- Channel 1 87
- Channel 2 88
- Logical Drive Configuration 89
- Physical Device Layout 91
- Configuring Arrays 94
- Configuration Strategies 95
- Maximizing Capacity 96
- Assigning RAID Levels 97
- Configuring Logical Drives 98
- Optimizing Data Storage 98
- Array Functions 99
- Random Array Deletion 101
- Configuration Module 102
- PERC 3/SC Hardware 103
- Installation 103
- Requirements 104
- Installation Steps 105
- PERC 3/SC Card Layout 105
- Step 1—Unpack 106
- Step 2—Power Down 106
- Step 3—Set Jumpers 107
- J9 I2C Interface Connector 108
- J5 Serial Port 108
- J8 Hard Disk LED 109
- J10 Term Power 109
- Step 4—Set SCSI Termination 110
- SCSI Termination 111
- Selecting a Terminator 111
- Step 5—Install PERC 3/SC 113
- Motherboard 114
- Step 6—Connect SCSI Cables 115
- Step 7—Set Target IDs 116
- Step 8—Power On Host System 117
- PERC 3/DC or PERC 119
- 3/DCL Hardware 119
- PERC 3/DC Card Layout 121
- PERC 3/DCL Card Layout 122
- J2, and J3 Termination Enable 124
- J9 Onboard BIOS Enable 124
- J10 NVRAM Clear 125
- J11 Serial Port 125
- J13 Dirty Cache LED 125
- J14 SCSI Activity LED 126
- J16 and J18 TERMPWR Enable 126
- PERC 3/DC and 3/DCL 128
- Step 7—Connect SCSI Cables 130
- Connect SCSI Devices 131
- Cable Suggestions 131
- PERC 3/QC Hardware 135
- PERC 3/QC Card Layout 137
- J14 Serial Port 141
- J17 Dirty Cache LED 141
- J19 Onboard BIOS Enable 141
- Figure 10-4 144
- Step 5—Install PERC 3/QC 145
- Step 8—Power on Host System 148
- WebBIOS Configuration Utility 149
- PERC 3 BIOS 151
- Configuration Utility 151
- Configuration On Disk 152
- Starting the PERC 3 BIOS 152
- Options 153
- Configure Menu 154
- Initialize Menu 155
- Objects Menu 155
- (continued) 156
- Logical Drive 157
- Virtual Sizing 157
- Physical Drive 158
- Battery Information 159
- Format Menu 160
- Rebuild Menu 160
- Check Consistency Menu 161
- Easy Configuration 162
- New Configuration 162
- View/Add Configuration 163
- Press <F4> 164
- Using Easy Configuration 165
- Using New Configuration 169
- Using View/Add Configuration 175
- 18 Set the Read Policy 179
- 19 Set the Read Policy 179
- Initializing Logical Drives 180
- Deletion) 181
- Formatting Physical Drives 182
- Batch Formatting 183
- Individual Formatting 183
- Rebuilding Failed Disk Drives 184
- Exiting the PERC 3 BIOS 186
- Setting Hardware Termination 186
- Clustering 187
- Dell Manager 189
- Starting Dell Manager 190
- Management Menu Options 191
- Dell Manager Menu Options 192
- Logical Drive Settings 193
- Physical Drive Menu 194
- 12-8 displays the menu items 195
- Reconstruct Menu 197
- Parameters 198
- Formatting Drives 202
- Exiting Dell Manager 204
- Troubleshooting 205
- Overview 206
- BIOS Boot Error Messages 207
- Other BIOS Error Messages 210
- Other Potential Problems 211
- Audible Warnings 212
- Appendix A: SCSI 213
- Cables and Connectors 213
- Appendix B: 215
- Warranties and Return 215
- General Provisions 221
- Guarantee 237
- Exclusions 237
- Making a Claim 237
- Glossary 239
- 238 Glossary 240
- Glossary 239 241
- 240 Glossary 242
- Glossary 241 243
- 242 Glossary 244
- Glossary 243 245
- 244 Glossary 246
- Glossary 245 247
- 246 Glossary 248
- Index 247 249
- 248 Index 250
- 249 Index 251
- 250 Index 252
- Printed in the U.S.A 254
- P/N 5C229 Rev. A04 254
Verwandte Produkte und Handbücher für Festplatten-Arrays Dell DCL and 3
Festplatten-Arrays Dell UCS-51 Betriebsanweisung
(68 Seiten)
(68 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern