Dell PERC 4/DC Bedienungsanleitung Seite 12
- Seite / 92
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Figure 3-3. PERC 4e/DC Controller Layout
Table 3-3.PERC4e/DCJumperandConnectorDescriptions
(Dirty Cache LED)
device. Optional.
J4
SCSI Termination Enable
Channel 1
3-pin header
Jumper pins 1-2 to enable software control of SCSI termination via drive detection.
Jumper pins 2-3 to disable onboard SCSI termination.
No jumper installed enables onboard SCSI termination. (See J17 and J18). This is the default.
J5
SCSI Termination Enable
Channel 0
3-pin header
J6
DIMM socket
DIMM socket
Socket that hold the memory module
J7
Internal SCSI Channel 0
connector
68-pin
connector
Internal high-density SCSI bus connector. Connection is optional.
J8
Internal SCSI Channel 1
connector
68-pin
connector
Internal high-density SCSI bus connector. Connection is optional.
J9
External SCSI Channel 0
connector
68-pin
connector
External very-high density SCSI bus connector. Connection is optional.
J10
Battery connector
3-pin header
Connector for an optional battery pack.
Pin-1 -BATT Terminal (black wire)
Pin-2Thermistor(whitewire)
Pin-3 +BATT Terminal (red wire)
J11
NVRAM clear
2-pin header
To CLEAR the configuration data, install a jumper.
J12
NMI jumper
2-pin header
Reserved for factory.
J13
32-bit SPCI Enable
3-pin header
Reserved for factory.
J14
Mode Select jumper
2-pin header
J15
Serial Port
3-pin header
Connector is for diagnostic purposes.
Pin-1 RXD (Receive Data)
Pin-2 TXD (Transmit Data)
Pin-3 GND (Ground)
J16
Onboard BIOS Enable
2-pin header
No jumper = Enabled (Default setting)
Jumpered = Disabled
J17
TERMPWR Enable Channel 0
2-pin header
Jumper installed enables TERMPWR from the PCI bus. Default setting.
No jumper installed enables TERMPWR from the SCSI bus. (See J4 and J5)
J18
TERMPWR Enable Channel 1
2-pin header
J19
External SCSI Channel 1
connector
68-pin
connector
External very-high density SCSI bus connector. Connection is optional.
J23
Serial EEPROM
2-pin header
To CLEAR configuration data, install a jumper.
D17 - D24
LEDs (located on back of card)
Indicate problems with the card.
Connector
Description
Type
Settings
J1
Write Pending Indicator
(Dirty Cache LED)
2-pin header
Connector for enclosure LED to indicate when data in the cache has yet to be written to the
device. Optional.
J2
Onboard BIOS Enable
2-pin header
No jumper = Enabled (Default setting)
Jumpered = Disabled
J4
I2C Header
3-pin header
Reserved
J5
SCSI Termination Enable
Channel 0
3-pin header
Jumper pins 1-2 to enable software control of SCSI termination via drive detection.
Jumper pins 2-3 to disable onboard SCSI termination.
No jumper installed enables onboard SCSI termination. (See J17 and J18). This is the default.
J6
SCSI Termination Enable
Channel 1
3-pin header
J7
Serial Port (RS232)
3-pin header
Connector is for diagnostic purposes.
Pin-1 RXD (Receive Data)
Pin-2 TXD (Transmit Data)
Pin-3 GND (Ground)
- User's Guide 1
- Overview 2
- RAID Controller Features 3
- Cache Memory 4
- Onboard Speaker 4
- Background Initialization 4
- Drive Migration 6
- LED Operation 6
- Installation Steps 10
- Connect SCSI Devices 14
- Cable Suggestions 14
- Step 6 Set Target IDs 15
- Step 7 Set SCSI Termination 15
- Step 8 Start the System 16
- Physical Device Layout 19
- Device Configuration 20
- Setting Hardware Termination 21
- Configuring Arrays 21
- Hot Spares 22
- Logical Drives 22
- Configuration Strategies 22
- Configuring Logical Drives 22
- Assigning RAID Levels 23
- Summary of RAID Levels 24
- Optimizing Storage 25
- Starting Dell Manager 28
- <F4> Key 29
- Objects Menu 30
- Using Easy Configuration 31
- Using New Configuration 32
- Drive Roaming 35
- Initializing Logical Drives 35
- Deleting Logical Drives 35
- Clearing Physical Drives 36
- Manual Rebuild – Batch Mode 37
- FlexRAID Virtual Sizing 38
- Checking Data Consistency 38
- Troubleshooting 40
- BIOS Boot Error Messages 41
- Other Potential Problems 42
- Cache Migration 42
- Audible Warnings 43
- FCC Notices (U.S. Only) 44
- Class B 44
- VCCI Class B Statement 45
- Back to Contents Page 46
- Configuration Features 49
- Firmware Upgrade 50
- SMART Hard Drive Technology 50
- Array Performance Features 51
- Fault Tolerance Features 52
- Software Utilities 52
- RAID Management Utilities 53
- Hardware Installation 54
- Step 3 Set Jumpers 55
- Logical Drive Configuration 66
- Optimizing Data Storage 68
- Glossary 89
Verwandte Produkte und Handbücher für Computerhardware Dell PERC 4/DC
Computerhardware Dell UPS 1000T Bedienungsanleitung
(147 Seiten)
(147 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.143 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern