manuale di istruzioniinstructions manualVersion 1.0Panorama Power MK2
5.1. Operating voltage and frequencyThe projector may operate at either 208, 230 or 240VAC at a frequncy of either 50 or 60Hz. Coemar presets (barring
3. Locate the ballast inside the base.3. Cables 32 and 34 determine the operating voltage. Move them to the required voltage, 208, 230 or 240V on the
5.3. Mains connectionMains cable characteristicsThe mains cable provided is thermally resistant, complying to the most recent international standards.
Panorama Power MK2 may operate in two modes:1. Using DMX 512 signal 2. In automatic “STAND ALONE” or “MASTER/SLAVE” (see section 8.0 Automated functio
6.2. Powering upPanorama Power MK2 is supplied with a 4 leaf barndoor which is generally in the closed position when shipping. After having completed
6.4. DMX functionsTo ignite the 2 lamps both channels number 5 and 6 must be set to a level betwen 141 and 255 and between 241 and 255 respectivelly.L
The display panel of the Panorama Power MK2 shows all the functions available; it is possible to change some of those parametersand to add some functi
7.2. Operating mode (MODE)By using the Panorama Power MK2 display panel it is possible to alter the operating mode of the projector. The following dia
7.3. Measure and test (MEAS)The internal microprocessor of the Panorama Power MK2 allows for several diagnostic and output parameters to be displayed.
7.4. Function settings (FUNC)The projector allows the altering of several functions and for selecting personalised settings.☞menuAOO1FUNCSTRDstandard
Panorama Power MK2 numero di serie/serial numberdata di acquisto/date of purchasefornitore/retailerindirizzo/addresscap/città/suburbprovincia/capital
7.5. Rapid scrollingVia the Panorama Power MK2 display it is possible to rapidly scroll through the various numbers displayed in the menu in the follo
The Panorama Power MK2 may operate without external DMX 512 signal. Using this function, it is possible to select the operatingmode (STAND ALONE or MA
8.2. MASTER/SLAVE modeAfter having connected the projectors, as described in section 8.1 MASTER/SLAVE signal connection, turn on power to the projec-t
Panorama Power MK2 utilises two Philips 575/2 MSR or MSD 575 lamps of 575W with a GX 9,5 base .All lamps are available from your Coemar service centre
3. Locate the two lamp assemblies, right and left. Remove the two screws “C”which hold the assemblies in place.5. Locate the lampholder “E”6. Insert t
9.2. Aligning the lamp in the optical pathAligning the lamp in the optical system is achieved via the 3 adjusters at the rear of the projector. This p
Fans and air passagesThe fans and air passages must be cleaned approximately every 6 weeks; theperiod for this periodic cleaning will depend, of cours
11.4. Electronic motor alignmentThe display panel of the Panorama Power MK2 allows for the electronic alignment of the projector’s motors in the optic
7. Press the + or - buttons until CL L is displayed (to access the lamp life counter for the left lamp) and press enter.8. The display will show SURE
Coemar s.p.a.via Inghilterra 2/A - 46042 Castel Goffredo (Mantova) Italyph. +39 0376/77521 - fax +39 0376/[email protected] si riserva il di
Index 1. Packaging and transportation Pag. 41.1. Packaging “41.2. Transportation “42. General information Pag. 42.1. Important safety information “42.
Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in compo-nentry and in the t
2.2. Warranty conditions1. The fixture is guaranteed for a period of 12 months from the date of purchase against manufacturing or materials defects2.
64.1. Mechanical installationDue to its IP44 protection rating, the Panorama Power MK2 may be installed in both covered and weather-exposed locations.
4.2. Safety chainIf the Panorama Power MK2 is affixed to a mobile structure the use of a safety chain designed to meet relevant safety standards is re
4.4. Adjusting fan shroudsAfter having adjusted the angle of inclination of the projector, you should follow these instructions to adjust the fan shro
The table below illustrates the various beam angles which can be achieved by the Panorama Power MK2 using the diffusion filters.Additional adjustment
Kommentare zu diesen Handbüchern