Dell E5430 + Port Replicator Euro 2 Bedienungshandbuch

Dell Latitude E5430Owner's ManualRegulatory Model: P27GRegulatory Type: P27G001

5. Remove the display bezel from the computer .Installing the Display Bezel1. Place the display bezel onto the display assembly.2. Starting from the t

b) battery5. Follow the procedures in After Working Inside Your Computer.Removing the Display Panel1. Follow the procedures in Before Working Inside Y

6. Remove the display panel from the display assembly.Installing the Display Panel1. Install the screws that secure the display brackets to the displa

4. Pry up the keyboard trim starting from the bottom edge.5. Work your way around the sides and the top edge of the keyboard trim.6. Lift upwards and

Installing the Keyboard Trim1. Align the keyboard trim to its compartment.2. Press along the sides of the keyboard trim until it snaps in place.3. Ins

4. Remove the screws that secure the keyboard in place.5. Lift the clip to release the keyboard cable and disconnect it from the computer .6. Flip the

8. Remove the keyboard from the computer .Installing the Keyboard1. Attach the keyboard flat flex cable to the keyboard.2. Affix the adhesive tape sec

4. Slide the access panel towards the front of the system and remove it from the computer.Installing the Access Panel1. Slide the access panel into it

3. Remove the screw that secures the optical drive.4. Push the screw tab away from the computer to release the optical drive from the drive bay.5. Rem

6. Remove the screws that secure the optical drive bracket.7. Remove the optical drive bracket.8. Disengage the optical drive bezel tabs to separate t

ContentsNotes, Cautions, and Warnings... 01 Working on Your

3. Remove the screws that secure the hard drive bracket in place.4. Use the tab to pull the hard drive bracket to release the hard drive from its conn

6. Remove the screws that secure the hard drive bracket.7. Remove the hard drive bracket from the hard drive.Installing the Hard Drive1. Engage the ha

Removing the Wireless Local Area Network (WLAN) Card1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) access pane

3. Install:a) access panelb) battery4. Follow the procedures in After Working Inside Your Computer.Removing the Right Base Panel1. Follow the procedur

4. Follow the procedures in After Working Inside Your Computer.Removing the Thermal Module1. Follow the procedures in Before Working Inside Your Compu

d) SD memory card4. Follow the procedures in After Working Inside Your Computer.Removing the Processor1. Follow the procedures in Before Working Insid

4. Remove the screws that secure the palm rest of the computer.5. Disconnect the LED board flat flex cable.26

6. Disconnect the media button flat flex cable.7. Disconnect the touch pad flat flex cable.8. Disconnect the fingerprint scanner flat flex cable.9. Di

e) LED board flat flex cable3. Tighten the screws on the palm rest.4. Tighten the screws at the bottom of the computer.5. Install:a) right base panelb

h) SD memory card4. Follow the procedures in After Working Inside Your Computer.Removing the Bluetooth Module1. Follow the procedures in Before Workin

Installing the Memory Module...

Removing the Audio Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD memory cardb) batteryc) access paneld) keyboar

Removing the Display Assembly1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD memory cardb) batteryc) access paneld) ke

5. Pull the antennas through the opening to the top of the computer.6. Remove the screws that secure the display assembly in place.7. Remove the displ

d) optical drivee) keyboardf) keyboard trimg) access panelh) batteryi) SD memory card6. Follow the procedures in After Working Inside Your Computer.Re

Installing the Right Support Frame1. Place the right support frame on the computer.2. Tighten the screws to secure the right support frame to the comp

g) optical driveh) hard drivei) right base panelj) thermal modulek) palm restl) express cardm) display assemblyn) right support frame3. Remove the scr

a) SD memory cardb) express cardc) batteryd) access panele) keyboard trimf) keyboardg) optical driveh) hard drivei) WLAN cardj) right base panelk) the

l) express cardm) SD memory card4. Follow the procedures in After Working Inside Your Computer.Removing the System Board1. Follow the procedures in Be

8. Remove the screws that secure the system board.9. Lift the right edge of the system board assembly and raise it to a 45–degree angle.38

10. Release the system board from the port connectors on the left and remove the system board.Installing the System Board1. Align the system board int

Docking Port Information...

d) palm reste) thermal modulef) right base panelg) hard driveh) optical drivei) keyboardj) keyboard trimk) access panell) batterym) SD memory card5. F

e) palmrestf) thermal moduleg) right base panelh) WLAN cardi) hard drivej) optical drivek) keyboardl) keyboard trimm) access paneln) batteryo) Express

Installing the Input/Output (I/O) Board1. Place the Input/Output (I/O) board in the computer.2. Tighten the screw to secure the Input/Output (I/O) boa

4. Remove the DC-in-jack.Installing the DC-in Jack1. Install the DC-in jack in the computer.2. Thread the DC-in cable in the routing channel.3. Instal

j) optical drivek) keyboardl) keyboard trimm) access paneln) batteryo) express cardp) SD memory card4. Follow the procedures in After Working Inside Y

4. Lift the system fan out of the computer.Installing the System Fan1. Place the system fan in the computer.2. Tighten the screws to secure the fan in

Removing the RJ11 Jack1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD memory cardb) express cardc) batteryd) access pa

c) left support framed) right support framee) display assemblyf) express card reader cageg) palm resth) thermal modulei) right base panelj) WLAN cardk

4. Remove the speaker cables from the routing channels.5. Lift the speaker out from the computer.Installing the Speakers1. Place the speakers in the c

g) palm resth) thermal modulei) right base panelj) WLAN cardk) hard drivel) optical drivem) keyboardn) keyboard trimo) access panelp) batteryq) expres

Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage and

50

SpecificationsSpecificationsNOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start

AudioInternal speaker amplifier 1W (RMS) per channelVolume controls keyboard function keys, program menusVideoType integrated on system boardControlle

DisplayLatitude E5430:Height 192.5 mm (7.57 inches)Width 324 mm (12.75 inches)Diagonal 355.60 mm (14.00 inches)Active ares (X/Y) 309.40 mm x 173.95 mm

TouchpadActive Area:X-axis 80.00 mmY-axis 45.00 mmBatteryType 4, 6 or 9-cell "smart" lithium ionDimensions:Height4-, 6-, and 9-cell 20.00 mm

AC AdapterType 65 W 90 W adapterInput voltage 100 VAC to 240 VAC 100 VAC to 240 VACInput current (maximum) 1.7 A 1.5 AInput frequency 50 Hz to 60 Hz 5

56

Additional InformationThis section provides information for the additional features that are part of your computer.Docking Port InformationThe docking

58

System SetupOverview System Setup allows you to:• change the system configuration information after you add, change, or remove any hardware in your co

Turning Off Your ComputerCAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.1.

GeneralBoot Sequence Allows you to change the order in which the computer attempts to find an operating system.• Diskette Drive• Internal HDD• USB Sto

System Configuration• AHCI• RAID On: This option is enabled by default.Drives Allows you to configure the SATA drives on board. All drives are enabled

System ConfigurationNOTE: All devices are enabled by default.You can also enable or disable Media Card.VideoLCD Brightness Allows you to set the displ

SecurityNon-Admin Setup Changes Allows you to determine whether changes to the setup options are allowed when an Administrator Password is set. If dis

PerformanceDefault Setting: Enable Intel TurboBoostHyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.Default Se

Power Management• Predominately AC use• Auto Charge: This option is enabled by default.• Custom ChargeIf Custom Charge is selected, you can also confi

Virtualization SupportVirtualization Allows you to enable or disable the Intel Virtualization Technology.Default Setting: Enable Intel Virtualization

DiagnosticsDiagnosticsDevice Status LightsTurns on when you turn on the computer and blinks when the computer is in a power management mode.Turns on w

68

Contacting DellContacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packi

Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommended

Removing the Battery1. Follow the procedures in Before Working Inside Your Computer.2. Slide the battery release latches into the unlock position.3. R

Removing the Subscriber Identity Module (SIM) Card1. Follow the procedures in Before Working On Your Computer.2. Remove the battery.3. Press and relea