Dell POWEREDGE M1000E Bedienungsanleitung Seite 43
- Seite / 126
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Fabric Watch Administrator’s Guide 23
53-1002752-01
Chapter
4
Fabric Watch Activation
In this chapter
•Interfaces for activating Fabric Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Interfaces for activating Fabric Watch
This section provides a brief overview of the available user interfaces for activating Fabric Watch.
Further details about Fabric Watch operations for each interface are provided later in this guide.
• Telnet session—Provides a command prompt where you can run Fabric OS commands to
configure your switch monitoring settings. See “Activating Fabric Watch using a Telnet session”
for instructions on how to activate Fabric Watch using a Telnet session.
• SNMP—Provides a receiver dedicated to monitoring the data center infrastructure; Brocade
switches and directors enable monitoring of specific incidents and trigger an SNMP alert
based on a user-defined threshold sending the alert to the dedicated SNMP trap receiver.
Configuring SNMP threshold alerts for Fabric OS switches requires using Web Tools to set up
SNMP on the Fabric OS switch. See “Activating Fabric Watch using SNMP” on page 24 for
instructions on how to set up SNMP.
• Web Tools—Provides a graphical user interface that can be launched from an Internet browser,
which allows you to launch a Fabric Watch window to configure switch monitoring settings.
Using Web Tools, you can configure thresholds, alarms, and e-mail notifications. See Chapter
9, “Fabric Watch Configuration Using Web Tools” for instructions on how to configure Fabric
Watch using the Web Tools GUI.
Activating Fabric Watch using a Telnet session
1. Connect to the switch and log in as admin.
2. Enter the following command, where switch represents the name or IP address of the switch:
telnet switch
After you enter this command, respond to the prompts for a username and password.
3. Enter the licenseShow command to determine if the Fabric Watch license is installed.
switch:admin> licenseshow
edzbzQStu4ecS:
Fabric Watch license
Performance Monitor license
Trunking license
Full Ports on Demand license - additional 16 port upgrade license
- Fabric Watch 1
- Document History 3
- Contents 5
- Chapter 7 Port Monitoring 7
- Chapter 8 System Monitoring 8
- 53-1002752-01 10
- About This Document 15
- What’s new in this document 16
- Document conventions 17
- Notes, cautions, and warnings 18
- Key terms 18
- Additional information 19
- Getting technical help 19
- Document feedback 20
- Fabric Watch overview 22
- Role-based access control 22
- Fabric Watch licensing 22
- Event behavior configuration 23
- Alert configuration 23
- Time base configuration 24
- Monitoring 24
- Post-processing of messages 24
- Switch monitoring components 25
- Security monitoring 26
- SFP monitoring 26
- Port monitoring 26
- System resource monitoring 27
- Logical switch support 28
- Fabric Watch event settings 29
- SNMP traps 30
- RASlog (switch event) 30
- Fabric Watch audit messages 31
- Data values 31
- • Fabric 32
- • Security 32
- • E_Port (Port subclass) 32
- • VE_Port (Port subclass) 32
- Fabric Watch Thresholds 33
- Threshold triggers 34
- Above event trigger 35
- Below event trigger 35
- Audit and RASlog messages 35
- Time bases 36
- Fabric Watch alarm behavior 37
- Elements 40
- Class Description 41
- Fabric Watch Activation 43
- FIGURE 6 Example OID tree 47
- Fabric Watch Configuration 49
- Disabling an e-mail alert 52
- Enabling an e-mail alert 52
- Sending a test e-mail message 53
- Notification configuration 54
- FW: Alarms are enabled 55
- Area Description 58
- Fabric class default settings 59
- Security class areas 60
- Threshold state 61
- SFP class areas 63
- • Send an SNMP alarm 66
- • Log a RASlog message 66
- • Send an e-mail alert 66
- Configuration recommendation 67
- 16 Gbps and QSFP monitoring 68
- Monitoring the SFP and QSFP 69
- Security classes 72
- Port Monitoring 75
- Port class default settings 77
- Port configuration 78
- Using the nosave command 79
- Port type: physical port 79
- <[slot/]port> 81
- E_Port class default settings 82
- • Area: Loss of Signal Count 84
- Port fencing 89
- Port fencing configuration 90
- Enabling port fencing 91
- Disabling port fencing 91
- Port fencing requirements 92
- System Monitoring 95
- 76 53-1002752-01 96
- Resource class settings 97
- Environment class settings 99
- CPU and memory 100
- Switch monitoring 101
- Switch status policy planning 102
- Monitor Health factors 103
- FRU monitoring 104
- Recommended FRU settings 106
- In this chapter 107
- • Polling Interval 108
- • Usage Limit 108
- • No. of Retries 108
- Configuring threshold traits 109
- Configuring threshold alarms 110
- Displaying alarms 113
- Enabling the e-mail alert 114
- Disabling the e-mail alert 115
- Fabric Watch Reports 117
- Switch Health report 119
- Switch Status Policy report 120
- Port Detail report 121
- Report item Description 122
Verwandte Produkte und Handbücher für Computerzubehör Dell POWEREDGE M1000E
(27 Seiten)
(94 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.663 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern