Dell POWEREDGE M1000E Bedienungsanleitung Seite 109
- Seite / 126
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Fabric Watch Administrator’s Guide 89
53-1002752-01
Fabric Watch Configuration Using Web Tools
9
4. Click the Alarm Configuration tab.
5. Select SNMP Trap, RAS log, or both options.
6. Click Apply.
Fabric Watch threshold configuration using Web Tools
The Threshold Configuration tab enables you to configure event conditions. From this tab, you
configure threshold traits, alarms, and e-mail configurations.
NOTE
Use the procedures in this section to configure threshold traits for all classes except for the FRU
class. Use the procedure described in “Configuring alarms for FRUs using Web Tools” on page 92 for
the FRU class.
Configuring threshold traits
Configure threshold traits to define a threshold for a particular class and area. You can configure
the following traits for a threshold:
• Time Base—The time base (minute, hour, day) for the area
• Low Boundary—The low threshold for the event-setting comparisons
• High Boundary—The high threshold for the event-setting comparisons
• Buffer Size—The size of the buffer zone used in event-setting comparisons
NOTE
When you are configuring the VE-Port > Packet Loss area thresholds, the packet loss threshold
values are a percentage. You can configure from 0.01% (low boundary) to 100.00% (high boundary).
To configure threshold traits, perform the following steps.
1. Click Fabric Watch in the Manage section of the Tasks menu.
2. Select the Threshold Configuration tab.
3. Select the Trait Configuration subtab.
4. In Fabric Watch Explorer, select a class.
5. Under Area Selection, select an area from the list.
This sets the units in the Units field.
The module displays two columns of trait information, labeled System Default and Custom
Defined. You cannot modify the information in the System Default column.
6. In the Activate Level area:
• Use the system default settings and proceed to step 11.
or
• Click Custom Defined to specify new settings and proceed to the next step.
7. If necessary, select a time to record the event in the Time Base field.
8. Enter the lowest boundary of the normal zone in the Low Boundary field.
- Fabric Watch 1
- Document History 3
- Contents 5
- Chapter 7 Port Monitoring 7
- Chapter 8 System Monitoring 8
- 53-1002752-01 10
- About This Document 15
- What’s new in this document 16
- Document conventions 17
- Notes, cautions, and warnings 18
- Key terms 18
- Additional information 19
- Getting technical help 19
- Document feedback 20
- Fabric Watch overview 22
- Role-based access control 22
- Fabric Watch licensing 22
- Event behavior configuration 23
- Alert configuration 23
- Time base configuration 24
- Monitoring 24
- Post-processing of messages 24
- Switch monitoring components 25
- Security monitoring 26
- SFP monitoring 26
- Port monitoring 26
- System resource monitoring 27
- Logical switch support 28
- Fabric Watch event settings 29
- SNMP traps 30
- RASlog (switch event) 30
- Fabric Watch audit messages 31
- Data values 31
- • Fabric 32
- • Security 32
- • E_Port (Port subclass) 32
- • VE_Port (Port subclass) 32
- Fabric Watch Thresholds 33
- Threshold triggers 34
- Above event trigger 35
- Below event trigger 35
- Audit and RASlog messages 35
- Time bases 36
- Fabric Watch alarm behavior 37
- Elements 40
- Class Description 41
- Fabric Watch Activation 43
- FIGURE 6 Example OID tree 47
- Fabric Watch Configuration 49
- Disabling an e-mail alert 52
- Enabling an e-mail alert 52
- Sending a test e-mail message 53
- Notification configuration 54
- FW: Alarms are enabled 55
- Area Description 58
- Fabric class default settings 59
- Security class areas 60
- Threshold state 61
- SFP class areas 63
- • Send an SNMP alarm 66
- • Log a RASlog message 66
- • Send an e-mail alert 66
- Configuration recommendation 67
- 16 Gbps and QSFP monitoring 68
- Monitoring the SFP and QSFP 69
- Security classes 72
- Port Monitoring 75
- Port class default settings 77
- Port configuration 78
- Using the nosave command 79
- Port type: physical port 79
- <[slot/]port> 81
- E_Port class default settings 82
- • Area: Loss of Signal Count 84
- Port fencing 89
- Port fencing configuration 90
- Enabling port fencing 91
- Disabling port fencing 91
- Port fencing requirements 92
- System Monitoring 95
- 76 53-1002752-01 96
- Resource class settings 97
- Environment class settings 99
- CPU and memory 100
- Switch monitoring 101
- Switch status policy planning 102
- Monitor Health factors 103
- FRU monitoring 104
- Recommended FRU settings 106
- In this chapter 107
- • Polling Interval 108
- • Usage Limit 108
- • No. of Retries 108
- Configuring threshold traits 109
- Configuring threshold alarms 110
- Displaying alarms 113
- Enabling the e-mail alert 114
- Disabling the e-mail alert 115
- Fabric Watch Reports 117
- Switch Health report 119
- Switch Status Policy report 120
- Port Detail report 121
- Report item Description 122
Verwandte Produkte und Handbücher für Computerzubehör Dell POWEREDGE M1000E
(27 Seiten)
(94 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.591 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern