Dell PowerEdge M IO Aggregator Bedienungshandbuch Seite 225
- Seite / 258
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Stacking Commands | 223
Example
Figure 21-5. show system stack-unit fanout Command Example
show system stack-unit stack-group
Displays the stack-groups present/configured for a M I/O Aggregator stack unit.
Syntax
show system stack-unit <unit-number> stack-group [configured]
Parameters
Command Modes
EXEC Privilege
Command
History
Related
Commands
Example
Figure 21-6. show system stack-unit stack-group Command Example
FTOS#show system stack-unit 0 fanout ?
configured Configured fan out ports
FTOS#show system stack-unit 0 fanout configured ?
| Pipe through a command
<cr>
FTOS#show system stack-unit 0 fanout configured
Configured fan out ports in stack-unit 0
Configured Next Boot
33 33
37 37
41 41
45 45
FTOS#
unit number
<0-5>
Number of the member stack unit. Valid values: 0 to 5. Default: 0.
Version 8.3.17.0 Supported on M I/O Aggregator
reload Reboots FTOS.
show system Displays the current status of all stack members or a specific member.
FTOS#show system stack-unit 0 stack-group ?
configured Configured stack groups
| Pipe through a command
<cr>
FTOS#show system stack-unit 0 stack-group configured
Configured stack groups in stack-unit 0
FTOS##show system stack-unit 0 stack-group
Stack group Ports
------------------------------------
0 0/33
1 0/37
2 0/41
3 0/45
FTOS#
- Notes, Cautions, and Warnings 2
- About this Guide 7
- Related Documents 8
- Before You Start 9
- DCB Support 10
- FCoE Connectivity 10
- Link Aggregation 11
- Link Tracking 11
- Where to Go From Here 12
- Before You Start 13
- 12 14
- CLI Basics 15
- Multiple Configuration Users 16
- Obtaining Help 17
- Combination Action 18
- Using the Keyword no 19
- Filtering show Commands 19
- Command Modes 20
- INTERFACE Mode 21
- LINE Mode 21
- MONITOR SESSION Mode 21
- PROTOCOL LLDP Mode 22
- File Management 23
- 27
- url url 30
- 36 38
- Control and Monitoring 39
- FTOS#configure 40
- FTOS(conf)# 40
- 54 56
- FTOS#show memory stack-unit 0 57
- Control and Monitoring 59
- Important Points to Remember 62
- Control and Monitoring 65
- [stack-unit unit-id 68
- Control and Monitoring 69
- Examples 69
- system component status 71
- 76 78
- BOOT_USER # 80
- 86 88
- Data Center Bridging 89
- 90 92
- Data Center Bridging 93
- FTOS# show dcb 95
- DCB Status : Enabled 95
- 96 98
- Data Center Bridging 99
- Field Description 100
- EXEC Privilege 101
- 104 106
- Overview 107
- DHCP Client Commands 107
- FIP Snooping 113
- FTOS#show fip-snooping config 114
- Global FC-MAP Value: 0X0EFC00 114
- FTOS# show fip-snooping enode 115
- FTOS# show fip-snooping fcf 116
- FIP Snooping 119
- IGMP Commands 121
- TenGigabitEthernet 124
- Interfaces 127
- Port Channel Commands 128
- Virtual LAN (VLAN) Commands 129
- FTOS(conf-po-failover-grp)# 132
- FTOS(conf)#int vlan 3 136
- FTOS(conf-if-vl-3)# 136
- FTOS(conf-lldp)#show conf 142
- FTOS(conf-lldp)# 142
- Line Description 144
- [interface] description 146
- FTOS#show int po 1 brief 149
- Codes: L - LACP Port-channel 149
- unit-id ] 151
- Items Description 152
- OK Status: Terminated 153
- G = GVRP VLAN 154
- P = primary VLAN 154
- C = community VLAN 154
- I = isolated VLAN 154
- Column Heading Description 155
- 158 160
- IPv4 Routing 161
- Lines Description 170
- • too short 174
- 174 176
- 178 180
- LACP Commands 181
- Layer 2 185
- 186 188
- LLDP Commands 189
- Port Monitoring 193
- Port Monitoring 197
- Commands 197
- FTOS(conf-mon-sess-11)# 198
- Quality of Service (QoS) 199
- Security 201
- port-number 206
- {1 206
- 206 208
- SNMP Commands 209
- Syslog Commands 209
- [facility-type] 212
- CONFIGURATION 212
- Example 1 217
- Example 2 217
- Disabled 219
- Stacking Commands 221
- 0-5 hard 222
- [stack 226
- Storm Control 227
- Storm-Control Enabled 228
- System Time 229
- FTOS#show calendar 230
- Enter one of the following: 235
- 234 236
- UFD Commands 237
- Debugging and Diagnostics 241
- Example 3 246
- 0-0 [port 248
- 0-0 {counters 248
- Example 4 249
- Example 250
- Example 7 251
- Example 8 251
- 0-5 port-set 0-0 [counters] 253
- Message Types 257
Verwandte Produkte und Handbücher für Server Dell PowerEdge M IO Aggregator
Server Dell PowerEdge R200 Bedienungshandbuch
(182 Seiten)
(182 Seiten)
Server Dell PowerEdge R610 Bedienungshandbuch
(184 Seiten)
(184 Seiten)
Server Dell EMC AX4-5I Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Server Dell 1955 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Server Dell 8/8 Technical Information
(147 Seiten)
(147 Seiten)
Server Dell PowerEdge BMX01 Bedienungshandbuch
(108 Seiten)
(108 Seiten)
Server Dell PowerEdge NM176 Betriebsanweisung
(292 Seiten)
(292 Seiten)
Server Dell PowerEdge VRTX Bedienungshandbuch
(150 Seiten)
(150 Seiten)
Server Dell PowerEdge NM176 Bedienungshandbuch
(454 Seiten)
(454 Seiten)
Server Dell 800 Wartungshandbuch
(75 Seiten)
(75 Seiten)
Server Dell POWEREDGE R710 Spezifikationen
(63 Seiten)
(63 Seiten)
Server Dell DAE Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Server Dell PowerVault 3000i Bedienungsanleitung
(14 Seiten)
(14 Seiten)
Server Dell PowerEdge FE600W Bedienungsanleitung
(34 Seiten)
(34 Seiten)
Server Dell PowerVault 3000i Spezifikationen
(32 Seiten)
(32 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern