Dell Dimension 4600C Spezifikationen

Dell™Dimension™4600CServiceManual Before You Begin Technical Overview Technical Specifications Advanced Troubleshooting System Setup Program Remov

Back to Contents Page Dell™Dimension™4600CServiceManual Closing the Computer Cover Closing the Computer Cover 1. Ensure that all cables are

Back to Contents Page Dell™Dimension™4600CServiceManual Opening the Computer Cover Opening the Computer Cover   1. Shut down the computer

Back to Contents Page I/O Panel Removing the I/O Panel   1. Shut down the computer through the Start menu. 2. Ensure that your computer and

Back to Contents Page 

Back to Contents Page Adding Memory You can increase your computer memory by installing memory modules on the system board. For information on the

8. Align the notch on the bottom of the module with the crossbar in the connector.   9. Insert the module into the connector until the modul

down your computer, turn them off now.  3. Disconnect any telephone or telecommunication lines from the computer. 4. Disconnect your computer a

Back to Contents Page Removing and Installing Parts Dell™Dimension™4600CServiceManual Back to Contents Page  Reattaching the Front Door Ad

Back to Contents Page Adding PC Cards (Optional)  You can add PC Cards to computers with integrated PC Card connectors. PC Card Types  The PC

Removing a PC Card    Press the eject button, and gently remove the card.  Back to Contents Page  NOTICE: Use the PC Card configuration uti

Back to Contents Page Advanced Troubleshooting Dell™Dimension™4600CServiceManual Diagnostic Lights Beep Codes System Messages Diagnosti

Back to Contents Page Power Supply Removing the Power Supply  1. Shut down the computer through the Start menu. 2. Ensure that your computer a

1. Slide the power supply into place. 2. Reconnect the DC power cables. 3. Connect the AC power cable to the power supply connector. 4. Run

Back to Contents Page Reattaching the Front Door To prevent damage to your computer, the front door is designed to "break away" if it is

Back to Contents Page AGP Card  YourDell™computerprovidesaconnectorforanAGPcard. 1. Shut down the computer through the Start menu. 2.

Installing an AGP Card   1. To add or replace the card, slide the card clip toward the front of the computer to ensure that the clip is unlocked.

Back to Contents Page Cards  YourDell™computerprovidesaslotforonelow-profile, 32-bit, 33-MHz card.  If you are installing or replacing

If necessary, disconnect any cables connected to the card. Grasp the card by its top corners, and ease it out of its connector. 4. Prepare the card

4. If you are removing the card permanently, install a filler bracket in the empty card-slot opening. If you need a filler bracket, see "Cont

Back to Contents Page Drives Your computer supports: l One hard drive (IDE, serial ATA) l One optional PC Card module l One CD or DVD drive 

2. Press in on the tabs on each side of the drive, slide the drive toward the I/O panel, and then remove the drive from the computer.  Instal

Beep Codes Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. This series of beeps, called

5. Check all connectors to be certain that they are properly cabled and firmly seated. 6. Close the computer cover. 7. Attach the computer st

Removing a PC Card Module 1. Remove the interposer board from the CD/DVD drive. 2. Remove the power cable from the PC Card module's power

See the documentation that came with the module for instructions on installing any software required for module operation. CD/DVD Drive   1. Sh

Installing a CD/DVD Drive 1. Unpack the drive and prepare it for installation. Check the documentation that accompanied the drive to verify tha

Back to Contents Page 

Back to Contents Page Microprocessor Removing the Microprocessor  1. Shut down the computer through the Start menu. 2. Ensure that your compu

10. Remove the two screws on the blower to remove it from the heat sink.   11. Pull the release lever straight up until the microprocessor is

4. Set the microprocessor lightly in the socket and ensure that all pins are headed into the correct holes. Do not use force, which could bend the

Back to Contents Page Technical Specifications Dell™Dimension™4600CServiceManual Microprocessor System Information Expansion Bus Memory

        Memory type 333-MHz DDR SDRAM (non-ECC) NOTE: DDR 333 memory performs at 266 MHz on 400 front- side bus processors. Drives Externa

System Messages    3-4-3 Search for video ROM failure 4-2-1 No time tick 4-2-2 Shutdown failure 4-2-3 Gate A20 failure 4-2-4 Unexpecte

 Back to Contents Page  Physical Height x Width x Depth (With stand) 32.3 x 9.5 x 35.6 cm (12.7 x 3.8 x 14.0 inches) 33.8 x 18.0 x 35.6 cm (13

Back to Contents Page Dell™Dimension™4600CServiceManual Attaching and Removing the Computer Stand Attaching and Removing the Computer Stand 

To remove the stand, perform the following steps.  1. Turn the computer over so that the stand is at the top. 2. Loosen the screw and lift the

Back to Contents Page System Board Removing the System Board  1. Shut down the computer through the Start menu. 2. Ensure that your computer a

 b. Remove the heat-sink assembly and microprocessor package from the existing system board and transfer them to the replacement system board. 2.

Back to Contents Page System Setup Program Dell™Dimension™4600CServiceManual Overview Entering the System Setup Program Clearing Forgotte

System Setup Screens The system setup program screens display the current configuration information for your computer. Information on the screen

 The following table shows Drive Configuration option information.   The following table shows Memory Information option information.   The follo

 The following table shows System Security option information.   Clearing Forgotten Passwords  If you forget your user or setup password, you ca

Turning on your computer with password jumper PWD1 installed reenables the password feature. Back to Contents Page 

Back to Contents Page 

Back to Contents Page Technical Overview Dell™Dimension™4600CServiceManual Internal View System Board Connectors and Sockets Power Supply

Power Supply The 160-W power supply can operate from an AC power source supplying 90-135 VAC or 180-265 VAC at 47-63 Hz. The power supply provide

DC Power Connector P1    DC Power Connector P2  Pin Number Signal name 18-AWG Wire 1 +3.3 VDC Orange 2 +3.3 VDC Orange 3 COM Black

  DC Power Connector P3    DC Power Connectors P4 and P5   DC Power Connector P6   Pin Number Signal Name 18-AWG Wire 1 COM Bl

 IDE Interface Cable Connections for Dell-Installed Drives   Serial ATA Interface Cable Connections for Dell-Installed Drives (Optional)  Plac

Back to Contents Page Dell™Dimension™4600CServiceManual For a complete list of abbreviations and acronyms, see the Tell Me How help file. Ifyou

Back to Contents Page Dell™Dimension™4600CServiceManual Turning Off Your Computer Turning Off Your Computer   1. Save and close any open f

Back to Contents Page Battery  A coin-cell battery maintains computer configuration, date, and time information. The battery can last several year

13. Connect your computer and devices to electrical outlets, and turn them on. 14. Enter system setup and restore the settings you recorded in ste

Back to Contents Page Before You Begin Dell™Dimension™4600CServiceManual Getting Started Thissectionprovidesproceduresforremovingand

Protecting Against Electrostatic Discharge Static electricity can harm delicate components inside your computer. To prevent static damage, discharge