Dell C300 Spezifikationen

Installing and Maintainingthe C300 System

10 | About this Guidewww.dell.com | support.dell.com

Installing and Maintaining the C150 System 112OverviewThe C300 is a high performance switch/router. The 10-slot system contains two slots for Route Pr

12 | Overviewwww.dell.com | support.dell.comC300 System Installation ProcessThe Dell Force10 recommended installation process is described below.Table

Installing and Maintaining the C150 System 133Preparing the SiteSite Selection CriteriaBefore beginning the installation process, make sure that the a

14 | Preparing the Sitewww.dell.com | support.dell.com• Make sure that the rack is permanently grounded to earth ground. The equipment rack must be gr

Installing C300 Fan Tray | 154Installing C300 Fan Tray The C300 chassis contains one field-replaceable fan tray. There are two types of fan tray that

16 | Installing C300 Fan Traywww.dell.com | support.dell.comTo install the fan tray: NOTE: The fan tray LED will remain lit when the chassis is ed up

Installing RPMs and Line Cards | 175Installing RPMs and Line CardsThe C300 System accommodates eight line cards and two RPMs.Route Processor ModulesTh

18 | Installing RPMs and Line Cardswww.dell.com | support.dell.comLine CardsLine cards are hot-swappable. Any line card can be inserted into any line

Installing RPMs and Line Cards | 19 NOTE: The fan tray face panel has slot number markings for the RPMs and line cards. Insert the fan tray before the

Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indi

20 | Installing RPMs and Line Cardswww.dell.com | support.dell.com5 Rotate the levers towards the card to seat the backplane connectors and line card

Installing RPMs and Line Cards | 21Figure 5-5. Installing a Line CardFigure 5-6. Installing an RPMfnC0005mpCard LeverCard GuideCard LeverCard Guidef

22 | Installing RPMs and Line Cardswww.dell.com | support.dell.com

Installing and Maintaining the C150 System 236RPM CablesConnecting the Console PortThe console port is an asynchronous serial port. If you connect a d

24 | RPM Cableswww.dell.com | support.dell.comAccessing the Console with a DB-9 AdapterYou can connect to the console using a RJ-45 to RJ-45 rollover

RPM Cables | 25Table 6-3. Pin Assignments Between C300 Console and DB-25 Adapter C300 System Console PortRJ-45 to RJ-45 Rollover Cable RJ-45 to DB-25

26 | RPM Cableswww.dell.com | support.dell.com

Installing AC Power Supplies | 277Installing AC Power SuppliesThe C300 has eight power supply slots at the front-bottom of the chassis (Figure 7-1). T

28 | Installing AC Power Supplieswww.dell.com | support.dell.comFigure 7-1. Power Supply LocationfnC0001mp

Installing AC Power Supplies | 29Figure 7-2. AC Power SupplyEach AC power supply has one LED as described in Table 7-1. This LED does not function un

Contents | 3Contents1 About this GuideInformation Symbols and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

30 | Installing AC Power Supplieswww.dell.com | support.dell.com WARNING: Leakage Current (High Touch Current) in AC-powered systems with more than 3

Installing AC Power Supplies | 31Power Over Ethernet (PoE)The C-Series can transmit power to Ethernet devices over the signal pairs of an Unshielded T

32 | Installing AC Power Supplieswww.dell.com | support.dell.com

Installing DC Power Entry Modules | 338Installing DC Power Entry ModulesThe C300 has eight supply slots at the front-bottom of the chassis (Figure 8-2

34 | Installing DC Power Entry Moduleswww.dell.com | support.dell.comCable and Connector RequirementsYou must provide your own cables to connect to a

Installing DC Power Entry Modules | 35Step Task (continued)4 Slide the PEM into slot 0 or 7 (see (Figure 8-2). If you are installing redundant PEMs, i

36 | Installing DC Power Entry Moduleswww.dell.com | support.dell.comFigure 8-3. Grounding7 Remove the outer nuts and washers from each of the remain

Installing DC Power Entry Modules | 37Status LEDThe status LED indicates the condition of the PEM.Removing a DC PEMThe left chassis PEM slot is labell

38 | Installing DC Power Entry Moduleswww.dell.com | support.dell.com

Installing and Maintaining the C150 System 399Powering UpBefore you supply power to the chassis, Dell Force10 recommends that you re-inspect your equi

4 | Contentswww.dell.com | support.dell.com8 Installing DC Power Entry ModulesRecommended Normal Operating Conditions . . . . . . . . . . . . . . . .

40 | Powering Upwww.dell.com | support.dell.com WARNING: The C300 operates in either of two voltage ranges. Each range supports a different supply co

Powering Up | 41Booting from the BOOT_USER PromptThe initial boot operation automatically brings up the system to the runtime CLI. To interrupt the au

42 | Powering Upwww.dell.com | support.dell.com

Installing and Maintaining the C150 System 4310Removing and Replacing ComponentsThis section provides instructions for removing and replacing the foll

44 | Removing and Replacing Componentswww.dell.com | support.dell.comFigure 10-1. Fan Tray (Left)To remove and replace the fan tray: Removing and Rep

Removing and Replacing Components | 45To remove and replace a supply: Removing and Replacing a Line Card WARNING: Do not remove a panel blank unless

46 | Removing and Replacing Componentswww.dell.com | support.dell.comRemoving and Replacing an RPM WARNING: After removing an RPM, place a panel blan

Removing and Replacing Components | 47To remove and replace a C300 RPM: Step Task 1 Unplug any network interface cables connected to the RPM.2 Extend

48 | Removing and Replacing Componentswww.dell.com | support.dell.com

Installing the Chassis | 4911Installing the Chassis Safety Considerations NOTE: Use an equipment lift or pallet jack when lifting or moving the chass

Contents | 5Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Product Recycling and Disposal .

50 | Installing the Chassiswww.dell.com | support.dell.comStep Task1 Install the equipment rack bar. This bar enables you to easily position the chass

Installing the Chassis | 514 Insert screws (provided with your rack) through the chassis rack-mounting bracket and into the equipment rack, and tighte

52 | Installing the Chassiswww.dell.com | support.dell.com

System Boot | 5312System BootWhen you supply power to the C300 system, the system performs a series of on self-tests. RPM and line card Status LEDs bl

54 | System Bootwww.dell.com | support.dell.comTo configure the chassis from the BOOT_USER prompt, use the following commands:CommandPurpose help or

System Boot | 55Refer to the C-Series FTOS Command Line Reference for BOOT_USER mode commands and commands for run-time modes. show interface manageme

56 | System Bootwww.dell.com | support.dell.com

The Compact Flash Card | 5713The Compact Flash Card Each RPM is designed with a slot (slot0:) to accommodate a Compact Flash Card (external compact fl

58 | The Compact Flash Cardwww.dell.com | support.dell.comTo remove the flash memory card:Formatting the Compact Flash Card New Compact Flash cards mu

Alarms | 59AAlarmsThe C300 System generates alarms for the following conditions:• fan tray status• supply status• RPMs status• high temperature on RP

6 | Contentswww.dell.com | support.dell.com

60 | Alarmswww.dell.com | support.dell.comAC Supplies and AlarmsDuring system boot, if a redundant supply is removed or fails, the FTOS generates a mi

Installing and Maintaining the C150 System 61BSystem SpecificationsPhysical DesignChassis Dimensions Table B-1. Chassis DimensionsParameter Specifica

62 | System Specificationswww.dell.com | support.dell.comComponent Dimensions System Specifications Table B-2. Component DimensionsComponent Catalog

System Specifications | 63Component Power Requirements NOTE: The listed requirement for the PoE version of line cards excludes the required power fo

64 | System Specificationswww.dell.com | support.dell.comCanadian Department of Communication Statement European Union EMC Directive Conformance State

System Specifications | 65Korea (MIC certification) Korea Certification Korea Information Safety Standards and Compliance Agency Certifications• CUS U

66 | System Specificationswww.dell.com | support.dell.comElectromagnetic Compatibility (EMC)Emissions• Australia/New Zealand: AS/NZS CISPR 22: 2006, C

System Specifications | 67In accordance with the European WEEE Directive, electrical and electronic equipment (EEE) is to be collected separately and

68 | System Specificationswww.dell.com | support.dell.com

Contacting Technical Support | 69CContacting Technical Support The iSupport WebsiteiSupport provides a range of documents and tools to assist you with

About this Guide | 71About this Guide This guide provides site preparation recommendations and instructions for installing the Dell Force10 C300 chass

70 | Contacting Technical Supportwww.dell.com | support.dell.comLocating Serial Numbers• The chassis serial number is below the barcode on the sticker

Contacting Technical Support | 713 When returning an RMA component, follow the packing and shipping directions in the Return Instructions document tha

72 | Contacting Technical Supportwww.dell.com | support.dell.com

www.dell.com | support.dell.comPrinted in the U.S.A.

8 | About this Guidewww.dell.com | support.dell.com WARNING: Building Supply Notice for AC Supply Use.This product relies on the building's inst

About this Guide | 9Related Documents For more information about the C300 system, refer to the following documents:•FTOS Command Reference for C-Serie