Dell XPS 210 Bedienungsanleitung

Dell™XPS™210ServiceManual Before You Begin About Your Computer Technical Overview Specifications Troubleshooting System Setup Removing the C

 Addressing Memory With 4-GB Configurations Your computer supports a maximum of 4 GB of memory when you use two 2-GB DIMMs. Current operating systems

 5. Replace the computer cover (see Replacing the Computer Cover).  6. Connect your computer and devices to electrical outlets, and then turn th

If you are installing or replacing a PCI Express card, follow the procedures in the next section. If you are removing but not replacing a card, see

 7. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot.  8. Before you close the card rete

 Removing a PCI Express Card  1. Follow the procedures in Before You Begin.  2. Gently push the release tab on the card retention door from the

 3. Lift the drive out of the computer and disconnect the power and hard-drive cables from the drive.  Installing a Hard Drive  1. Follow the p

 6. Check all connectors to be certain that they are properly cabled and firmly seated.  7. Gently slide the drive into the open bay until the

1. Follow the procedures in Before You Begin.  2. Pull up on the drive release latch and slide the drive towards the back of the computer.  3.

 4. Connect the data cable to the CD/DVD connector on the system board.  5. Gently position the drive until it clicks into place.  6. Chec

 4. Carefully, lift the drive away from the computer.  5. Disconnect the floppy drive interface cable from the system board (see System Board C

Back to Contents Page  About Your Computer Dell™XPS™210ServiceManual Front View Back View Front View -- NOTE: The front panel door

 4. Attach the interface cable to the system board (see System Board Components).  5. Check all cable connections, and fold cables out of the

 1. Follow the procedures in Before You Begin.  2. Remove the CD/DVD drive, if installed (see Removing a CD/DVD Drive).  3. Remove the hard d

 3. Slide the drive into place until you feel a click or feel the drive securely installed.  4. Connect the interface cable to the back of the M

 1. Follow the procedures in Before You Begin.  2. Remove the CD/DVD drive, if installed (see Removing a CD/DVD Drive).   3. Remove the two

4. Disconnect the fan power cable from the CPUFAN connector on the system board (see System Board Components).  5. Press the fan release lever, t

 5. Open the processor cover, and then carefully remove the processor from the socket. Leave the release lever extended in the release position s

 5. Gently place the processor in the socket and check to ensure that the processor is positioned correctly.  6. When the processor is fully seat

 4. Install the new modem: a. Connect the T-shaped connector of the modem cable to the modem. b. Align the modem with the screw holes and pre

 5. Slide the power supply approximately 1 inch toward the front of the computer.  6. Carefully lift the power supply out of the computer. 

5. Before you remove the existing system board, visually compare the replacement system board to the existing board to ensure that you have the correc

Back View  Back Panel Connectors  NOTICE: To avoid losing data, do not use the power button to turn off the computer. Instead, perform an operat

Front I/O Panel    Removing the Front I/O Panel  1. Follow the procedures in Before You Begin.  2. Remove the heat sink (see Removing the He

2. Press the case so that the tabs fix firmly into the slots in the chassis.  3. Press the LED card case release lever and slide the case towards

Front Panel  1. Follow the procedures in Before You Begin.  2. Remove the CD/DVD drive (see Removing a CD/DVD Drive).  3. Remove the option

 13. Lift up on the front panel to release the top two tabs that attach it to the computer chassis.  14. Pull up on the lower tab to release it

Back to Contents Page  Specifications Dell™XPS™210ServiceManual  Processor Processor types Intel®Pentium®4, Pentium®D, Celeron®D, Intel C

x1 slot bidirectional speed: 500 MB/sec x16 slot bidirectional speed: 8 GB/sec PCI Express:  connector one x1 connector size 36 pins connector data w

Back to Contents Page   ControlsandLights Power control push button Power light green light — Blinking green in sleep state; solid green for powe

Back to Contents Page  System Setup Dell™XPS™210ServiceManual Overview Entering System Setup System Setup Options Boot Sequence C

System Setup Options NOTE: Depending on your computer, BIOS version, and installed devices, the items listed in this section may not appear, or may

Video Primary Video (Auto default) Specifies which video controller is primary when two video controllers are present on the computer. Auto enables th

Back to Contents Page  1 link integrity light l Green — A good connection exists between a 10-Mbps network and the computer. l Orange — A good co

Boot Sequence This feature allows you to change the boot sequence for devices.  Option Settings l Onboard or USB Floppy Drive — The computer attem

You can use this feature, for example, to restart your computer to a USB device such as a floppy drive, memory key, or CD-RW drive.  1. If you are bo

 11. Connect your computer and devices to electrical outlets, and then turn them on.  12. Assign a new system and/or administrator password, as ne



Back to Contents Page  Technical Overview Dell™XPS™210ServiceManual Inside View of Your Computer System Board Components Power Supply D

 Jumper Settings Jumper locations are shown below. 1 processor fan connector (CPUFAN) 16 modem connector (RJ11) 2 processor connector (CPU) 17 RJ11

- Power Supply DC Connector Pin Assignments  DC Power Connector P1  Jumper  Setting  Description CLRPSWD Password features are enabled (d

 DC Power Connector P2  DC Power Connector P3   Pin Number  Signal Name  18-AWG Wire 1 +3.3 VDC Orange 2 +3.3 VDC Orange 3 COM Black 4 +5 VD

 DC Power Connector P5 Back to Contents Page   Pin Number  Signal Name  18-AWG Wire 1 COM Black 2 +5 VDC Red 3 KEY N/A 4 +3.3 VDC Orange

Back to Contents Page  Troubleshooting Dell™XPS™210ServiceManual Dell Diagnostics System Lights Diagnostic Lights Beep Codes Dell

Back to Contents Page  Before You Begin Dell™XPS™210ServiceManual Getting Started Recommended Tools Turning Off Your Computer Before

For any problem encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and proble

To help you troubleshoot a problem, your computer has four lights labeled 1, 2, 3, and 4 on the front panel (see Front View). When the computer starts

Back to Contents Page  1-2-1 Programmable interval timer failure 1-2-2 DMA initialization failure 1-2-3 DMA page register read/write failure 1-3 Vide

 2. Disconnect any telephone or network cables from the computer.  3. Disconnect your computer and all attached devices from their electrical out

Back to Contents Page  Replacing the Computer Cover Dell™XPS™210ServiceManual   1. Ensure that all cables are connected and folded out of th

Back to Contents Page  Removing the Computer Cover Dell™XPS™210ServiceManual    1. Follow the procedures in Before You Begin.  2. Lay yo

Back to Contents Page  Removing and Installing Parts Dell™XPS™210ServiceManual Memory You can increase your computer memory by installing me