Dell PowerVault MD3060e Bedienungshandbuch

Dell PowerVault MD3060e Storage EnclosureOwner's ManualRegulatory Model: E08J SeriesRegulatory Type: E08J001

Power Supply Module Features And Indicators NOTE: Your storage enclosure is shipped with two IEC C19 to C20 jumper cords. Connect the C19 plug to the

Item Indicator or Connector Icon DescriptionOff Indicates that you cannot remove the power supply module from the system.6 Service action required ind

Figure 7. Slot Numbering on the Disk DrawerNOTE: If you need to install less than 12 physical disks, you must follow the recommended physical disk ins

Item Indicator, Button, or ConnectorIcon Description1 SAS IN port 0 For SAS connection of the storage enclosure to a server, RAID controller, or anoth

NOTE: For all PowerVault documentation, go to dell.com/powervaultmanuals and enter the system Service Tag to get your system documentation.• Rack Inst

2Installing and removing system components Recommended ToolsYou may need the following items to perform the procedures in this section:• #2 Phillips s

Figure 9. Removing and Installing the Front Bezel1. release latches (2) 2. front bezel3. guide pins (4)Removing The Front BezelYou must remove the fro

Figure 10. Inside the Physical-Disk Drawer1. release latch (2) 2. physical-disk bay (12)3. physical-disk connector (12) 4. SAS cable connection (2)5.

Figure 11. Opening and Closing the Physical-Disk Drawer1. physical-disk drawer 2. release latches (2)Closing The Physical-Disk DrawerCAUTION: Many rep

Removing The Physical-Disk DrawerCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

Figure 12. Removing and Installing the Physical-Disk Drawer1. physical-disk drawer 2. release tabs (2)Installing The Physical-Disk DrawerCAUTION: Many

6. Install the front bezel.Physical DisksYour system supports up to sixty 2.5 inch or 3.5 inch SAS and nearline SAS physical disks and up to 25 2.5 in

Figure 13. Removing and Installing the 2.5 Inch Physical Disk in a 2.5 Inch Physical-Disk Carrier1. 2.5 inch physical drive cage 2. guide pins (4)3. r

Figure 14. Removing and Installing the 3.5 Inch Physical Disk in a 3.5 Inch Physical-Disk Carrier1. 3.5 inch physical disk 2. release handle3. slots o

Removing A Physical Disk From A Physical-Disk DrawerCAUTION: Many repairs may only be done by a certified service technician. You should only perform

Installing A Physical Disk In A Physical-Disk DrawerCAUTION: Many repairs may only be done by a certified service technician. You should only perform

Removing The SAS Chain Cable(s)CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and s

Figure 17. Removing and Installing the SAS Chain Cable(s)1. left cooling fan module bay 2. right cooling fan module bay3. SAS cable connector on the m

CAUTION: If you are hot swapping the SAS cable chains, ensure that you complete the procedure on one side within ten minutes to avoid over heating of

Figure 18. Removing and Installing an Enclosure Management Module1. enclosure management module 2. release lever3. release tabInstalling An Enclosure

Contents1 About your system... 5Introduction...

When two identical power supplies are installed, the power supply configuration is redundant. In redundant mode, power is supplied to the system equal

Figure 19. Removing and Installing the power supply module1. power supply 2. release latch (2)Installing A Power Supply ModuleCAUTION: Many repairs ma

Cooling Fan ModulesYour system supports two hot-swappable cooling fan modules.Removing A Cooling Fan ModuleCAUTION: Many repairs may only be done by a

Figure 20. Removing and Installing the Cooling Fan Module1. cooling fan module release latch 2. cooling fan module handle3. cooling fan moduleInstalli

3Troubleshooting your systemSafety first—for you and your systemCAUTION: Many repairs may only be done by a certified service technician. You should o

CAUTION: Power supply modules are hot-swappable. The enclosure can operate on a single power supply module; however both modules must be installed to

Troubleshooting A Wet Storage EnclosureCAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooti

4Technical SpecificationsPhysical DisksPhysical disks Up to sixty 3.5 inch or 2.5 inch SAS or nearline SAS physical disks or 2.5 inch SAS SSDsNOTE: Fo

PowerNOTE: This system is also designed to be connected to IT power systems with a phase to phase voltage not exceeding 230 V.EnvironmentalNOTE: For a

EnvironmentalAltitudeOperating Maximum 3000 m (9,842 ft)Storage Maximum 12192 m (40,000 ft)Airborne contaminant levelClass G1 as defined by ISA-S71.04

Cooling Fan Modules... 32Removi

5Getting help Locating your system service tagYour system is identified by a unique Express Service Code and Service Tag number. The Express Service C

1About your system IntroductionCAUTION: See the Safety, Environmental, and Regulatory Information document for important safety information before fol

Front-Panel Indicators Figure 2. Front-Bezel IndicatorsFigure 3. Front-Panel Indicators6

Item Indicator Icon Description1 Power-on indicator The power-on indicator lights green when at least one power supply module is supplying power to th

Item Indicator Icon Description8 Drive activity indicatorNOTE: The associated physical disk is indicated by a number (0 to 11) that is displayed above

Cooling Fan Module LED Indicator CodesFigure 5. Cooling Fan Module IndicatorsItem Indicator Icon Description1 Power indicator The power indicator ligh