Dell 6430u Bedienungshandbuch

Dell Latitude 6430uOwner's ManualRegulatory Model: P36GRegulatory Type: P36G001

Figure 2. Inside view — back1. wireless local area network (WLAN) / wireless gigabit alliance (WiGig) card2. system fan3. thermal module4. memory5. sm

Figure 3. Inside view — front1. sniffer board2. hall sensor3. smart card board4. system board5. coin-cell batteryRemoving the Secure Digital (SD) Card

Removing the Battery1. Follow the procedures in Before Working Inside Your Computer.2. Slide the release latch to unlock the battery, and slide to rem

Installing the Base Cover1. Place the base cover to align with the screw holes on the computer.2. Tighten the screws to secure the base cover to the c

Installing the mSATA SSD Card1. Place the mSATA SSD card in its slot in the computer.2. Tighten the screw to secure the mSATA SSD card to the computer

NOTE: The WiGig card has three antenna cables.Installing the WLAN / WiGig Card1. Insert the WLAN/WiGig card into its connector at a 45–degree angle in

4. Install:a) base coverb) SD cardc) battery5. Follow the procedures in After Working Inside Your Computer.Removing the TAA Board1. Follow the procedu

Installing the System Fan1. Place the system fan in its slot on the computer.2. Tighten the screws that secure the system fan to the computer.3. Conne

4. Remove the screws that secure the keyboard to the computer.5. Using a flat screwdriver, release the snaps.18

6. Flip the computer and remove the keyboard from the computer.Installing the Keyboard1. Slide the keyboard into its compartment and ensure that it cl

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

d) keyboard3. Disconnect the media-board cable, power-switch cable, touchpad cable, fingerprint-scanner cable and speaker cable.4. Remove the screws t

5. Flip the computer and remove the screws that secure the palmrest assembly to the base of the computer and flip open the lower assembly.6. Press aga

d) power-switch cablee) media-board cable6. Install:a) keyboardb) base coverc) SD cardd) batteryRemoving the Power-Switch Board1. Follow the procedure

c) base coverd) keyboarde) palmrest assembly3. Un-route the fingerprint-scanner cable. Remove the screw that secures the fingerprint-scanner bracket t

Installing the Display Bezel1. Place the display bezel on the display assembly.2. Starting from the top corner, press on the display bezel and work ar

4. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel.5. Remove the display panel from the display assembly.I

Removing the Power LED Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) display bezelc) display panel3. Rem

Installing the Camera1. Connect the LVDS and camera cable.2. Place the camera module in its slot in the computer.3. Tighten the screw to secure the ca

Installing the Speakers1. Align the speakers in the original position in the computer.2. Route the speaker cables through the routing channels.3. Tigh

Installing the Coin-Cell Battery1. Place the coin-cell battery in its slot.2. Connect the coin-cell battery cable.3. Install:a) palmrest assemblyb) ke

ContentsNotes, Cautions, and Warnings... 21 Working on

4. Remove the bluetooth card. Disconnect the cable from the card.Installing the Bluetooth Card1. Replace the bluetooth card in its slot.2. Connect the

Removing the Smart-Card Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) SD cardc) base coverd) keyboarde)

5. Follow the procedures in After Working Inside Your Computer.Removing the Smart-Card Cage1. Follow the procedures in Before Working Inside Your Comp

a) palmrest assemblyb) keyboardc) base coverd) SD carde) battery5. Follow the procedures in After Working Inside Your Computer.Removing the Hall Senso

Removing the Sniffer Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) SD cardc) base coverd) keyboarde) pal

4. Disconnect the antenna cables from the wireless solution.5. Remove the screws that secure the display assembly to the base of the computer and slid

Installing the Display Assembly1. Insert the LVDS and wireless antenna cables through the holes on the base chassis and connect them.2. Place the disp

e) palmrest assemblyf) display assemblyg) system board3. Disconnect the power-connector cable from the computer.Installing the Power Connector1. Conne

4. Disconnect the smart-card cable, hall-sensor cable and coin-cell battery cable.5. Remove the screws that secure the power-connector bracket to the

Installing the System Board1. Place the system board on the chassis.2. Tighten the screws to secure the system board to the computer.3. Place the powe

Installing the Display Bezel...

b) SD cardc) base coverd) keyboarde) palmrestf) display assemblyg) power connectorh) system board3.4. Remove the screws that secure the thermal module

3System SetupSystem Setup OverviewSystem Setup allows you to:• change the system configuration information after you add, change, or remove any hardwa

NOTE: For most of the system setup options, changes that you make are recorded but do not take effect until you restart the system.Table 1. Navigation

System Setup OptionGeneralTable 2. GeneralOption DescriptionSystem Information This section lists the primary hardware features of your computer.• Sys

Option Description• Enable UEFI Network Stack: This allows you to enable UEFI Networking Protocols in pre-OS and early OS networking environment.SATA

Option DescriptionUnobtrusive Mode This feature, when enabled, pressing Fn+B allows you to turn on/off all light and sound emissions including system

Option DescriptionNOTE: If Strong Password is enabled, Admin and System passwords must contain at least one uppercase character, one lowercase charact

Table 6. Secure BootOption DescriptionSecure Boot Enable Allows you to enable or disable the Secure Boot Feature. For Secure Boot to the enables, the

Table 8. Power ManagementOption DescriptionAC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter i

Option DescriptionNOTE: All charging mode may not be available for all the batteries.Intel Smart Connect Technology Allows you to periodically sense n

5 Specifications... 556 Getti

Table 11. WirelessOption DescriptionWireless Switch Allows to set the wireless devices that can be controlled by the wireless switch. The options are:

4TroubleshootingEnhanced Pre-Boot System Assessment (ePSA) DiagnosticsThe ePSA diagnostics (also known as system diagnostics) performs a complete chec

Turns on when wireless networking is enabled.If the computer is connected to an electrical outlet, the battery light operates as follows:Table 15. Bat

Code Cause and Troubleshooting StepsMemory failure5 Real-time clock power failCMOS battery failure6 Video BIOS test failureVideo card failure7 CPU - c

54

5SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more in

Feature SpecificationInterface:Internal high definition audioExternal microphone-in/stereo headphones/external speakers connectorSpeakers twoInternal

Table 24. DisplayFeature SpecificationType HD Anti GlareDimensions:Height 205.60 mm (8.09 inches)Width 320.90 mm (12.63 inches)Diagonal 355.60 mm (14.

Table 27. BatteryFeature SpecificationType lithium ion 3 cell (36 WHr) Ultra mobileDimensions:Depth 110.73 mm (4.36 inches)Height 9.70 mm (0.38 inch)W

Feature SpecificationNon-Operating -40 °C to 70 °C (-104 °F to 158 °F)Table 29. PhysicalFeature DescriptionHeight 20.90 mm (0.82 inch)Width 338.20 mm

6

60

6Getting HelpContacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the c

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende