Dell Studio XPS 8100 (Late 2009) Bedienungsanleitung

Dell™StudioXPS™8100ServiceManual Notes, Cautions, and Warnings Information in this document is subject to change without notice. ©2009DellIn

Removing PCI and PCI Express Cards  1. Follow the procedures in Before You Begin.  2. Remove the computer cover (see Removing the Computer Co

 8. If you are removing the card permanently, install a filler bracket in the empty card-slot opening. Replacing PCI and PCI Express Cards  1.

 5. Connect any cables that should be attached to the card. See the documentation for the card for information about the card's cable connec

Back to Contents Page  Coin-Cell Battery Dell™StudioXPS™8100ServiceManual Removing the Coin-Cell Battery Replacing the Coin-Cell Battery

 3. Replace the computer cover (see Replacing the Computer Cover).  4. Connect your computer and devices to electrical outlets, and then turn t

Back to Contents Page  Computer Cover Dell™StudioXPS™8100ServiceManual Removing the Computer Cover Replacing the Computer Cover   

 6. Replace the thumbscrew that secures the computer cover to the chassis.  7. Place the computer in an upright position. Back to Contents

Back to Contents Page  Processor Dell™StudioXPS™8100ServiceManual Removing the Processor Replacing the Processor      Removing t

  6. Gently lift the processor to remove it from the socket. Leave the release lever extended in the release position so that the socket is ready

Back to Contents Page  Before You Begin Dell™StudioXPS™8100ServiceManual Technical Specifications Recommended Tools Turning Off Your

 8. Pivot the socket release lever back toward the socket, and snap it into place to secure the processor.  9. Clean the thermal grease from the

Back to Contents Page  Drives Dell™StudioXPS™8100ServiceManual Hard Drive Optical Drive Media Card Reader     Hard Drive  Re

 7. If removing the hard drive changes the drive configuration, ensure that you reflect these changes in the system setup (see System Setup).  Rep

 7. Set aside the optical drive in a secure location.  Replacing the Optical Drive  1. Follow the procedures in Before You Begin.  2. Remov

 10. See the documentation that came with the drive for instructions on installing any software required for drive operation.  11. Check the Sy

5. Replace the top cover (see Replacing the Top Cover).  6. Replace the optical drive (see Replacing the Optical Drive).  7. Replace the front

Back to Contents Page  Fans Dell™StudioXPS™8100ServiceManual Chassis Fan Processor Fan and Heat Sink Assembly     Chassis Fan 

 3. Replace the four screws that secure the chassis fan to the chassis.  4. Connect the chassis fan cable to the system board connector (see Sy

2. Clean the thermal grease from the bottom of the heat sink.   3. Apply new thermal grease to the top of the processor.  4. If required, rota

Back to Contents Page  Front USB Panel Dell™StudioXPS™8100ServiceManual Removing the Front USB Panel Replacing the Front USB Panel  

   1. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched.  2. Turn off your computer (see Turnin

Replacing the Front USB Panel   1. Follow the procedures in Before You Begin.  2. Align and slide the front USB panel clamp into the front USB

Back to Contents Page  Graphics Card Bracket Dell™StudioXPS™8100ServiceManual Removing the Graphics Card Bracket Replacing the Graphics

 5. Replace the computer cover (see Replacing the Computer Cover). Back to Contents Page 

Back to Contents Page  Memory Module(s) Dell™StudioXPS™8100ServiceManual Removing the Memory Module(s) Replacing the Memory Module(s)

 3. Align the notch on the bottom of the memory module with the tab in the connector.   4. Insert the memory module into the connector until

8. Right-click the My Computer icon on your Microsoft®Windows® desktop and click Properties.  9. Click the General tab.  10. To verify that t

Back to Contents Page  Power Supply Dell™StudioXPS™8100ServiceManual Removing the Power Supply Replacing the Power Supply     Rem

  3. Replace the four screws that secure the power supply to the chassis.  4. Connect the DC power cables to the system board and drives (see Sy

Back to Contents Page  Power Button Module Dell™StudioXPS™8100ServiceManual Removing the Power Button Module Replacing the Power Button

 1. Follow the procedures in Before You Begin.  2. Align and push the power button module tabs into the slots in the top panel.  3. Connect t

Back to Contents Page  Front Bezel Dell™StudioXPS™8100ServiceManual Removing the Front Bezel Replacing the Front Bezel     Removi

Back to Contents Page  System Board Dell™StudioXPS™8100ServiceManual Removing the System Board Replacing the System Board Entering th

9. Lift the system board up and out.  10. Compare the system board that you just removed with the replacement system board to ensure that they are

Back to Contents Page  System Setup Dell™StudioXPS™8100ServiceManual Overview Clearing Forgotten Passwords Clearing CMOS Settings 

Processor Cache L1 Displays the processor L1 cache size Processor Cache L2 Displays the processor L2 cache size Processor Cache L3 Displays the proces

 Boot Sequence This feature allows you to change the boot sequence for devices.  Boot Options l Hard Drive — The computer attempts to boot from th

Clearing Forgotten Passwords    1. Follow the procedures in Before You Begin.  2. Remove the computer cover (see Removing the Computer Cover)

 4. Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2.  5. Wait for approximately five seconds to clear the CMOS settin

Back to Contents Page  Technical Overview Dell™StudioXPS™8100ServiceManual Inside View of Your Computer System Board Components  Ins

Back to Contents Page  1 Power connector (PWR2) 2 processor socket 3 processor fan connector (CPU_FAN1) 4 memory module connector (DIMM3) 5 memory

Back to Contents Page Dell™StudioXPS™8100ServiceManual Information in this document is subject to change without notice. ©2009DellInc.All

1. Follow the procedures in Before You Begin.  2. Align and insert the front bezel clamps into the front panel slots.  3. Rotate the front bez

Back to Contents Page  Top Cover Dell™StudioXPS™8100ServiceManual Removing the Top Cover Replacing the Top Cover     Removing the

2. Align the tabs in the top cover with the slots in the top panel.  3. Press and slide the top cover towards the back of the computer, until it c

Back to Contents Page  Top I/O Panel Dell™StudioXPS™8100ServiceManual Removing the Top I/O Panel Replacing the Top I/O Panel     

Replacing the Top I/O Panel  1. Follow the procedures in Before You Begin.  2. Align the screw holes in the top I/O panel with the screw holes

Back to Contents Page  Flashing the BIOS Dell™StudioXPS™8100ServiceManual The BIOS may require flashing when an update is available or when

Back to Contents Page  Bluetooth Assembly Dell™StudioXPS™8100ServiceManual Removing the Bluetooth Assembly Replacing the Bluetooth Assem

 1. Follow the procedures in Before You Begin.  2. Align the Bluetooth assembly tab to the Bluetooth assembly slot in the front panel, and push t

Back to Contents Page  PCI and PCI Express Cards Dell™StudioXPS™8100ServiceManual Removing the Card Retention Bracket Replacing the Card