Dell 3030 Bedienungshandbuch

OptiPlex 3030 All-in-OneOwner's ManualRegulatory Model: W10BRegulatory Type: W10B001

1. SD Memory card reader2. memory module3. speaker connector4. touch connector5. control board connector6. HDD connector7. ODD connector8. SATA power

3Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Removing t

3. Perform the following steps as shown in the illustration:a. Using a scribe, pry the edges of the computer [1].b. Remove the back cover from the com

3. Remove the screw that secures the optical drive to the computer . Slide the optical drive out of the computer.Installing the Optical Drive1. Slide

3. Perform the following steps as shown in the illustration:a. Push the hard-drive bracket to release it from its lock [1].b. Lift the hard drive from

6. Pry the hard-drive bracket apart to release the hard drive. Remove the hard drive from the hard-drive bracket.Installing the Hard Drive1. Insert th

3. Disconnect the cables from the convertor board. Remove the screws and lift the convertor board from the computer.Installing the Convertor Board1. T

3. Perform the following steps as shown in the illustration:a. Slide to release the memory cover from the computer [1].b. Remove the memory cover from

3. Perform the following steps as shown in the illustration:a. Remove the screws that secure the system-board shield to the computer [1].b. Lift the s

3. Perform the following steps as shown in the illustration:.a. Remove the screw that secure the heatsink to the computer [1].b. Remove the screws tha

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

3. Perform the following steps as shown in the illustration:a. Remove the screws that secure the speaker cover to the computer [1].b. Release the spea

5. Perform the following steps as shown in the illustration:a. Disconnect the speaker cable from the system board [1].b. Release the cable from the ta

3. Align the speaker cover on the computer and tighten the screws to secure it.4. Install:a. system-board shieldb. back coverc. standd. stand cover5.

Removing the System Fan1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a. stand coverb. standc. back coverd. System-board sh

Removing the Power-Switch Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a. stand coverb. standc. back cover3. Peel th

Installing the Power-Switch Board1. Insert the power-switch board into its slot on the computer and fix the tape to secure it. Connect the power-switc

3. Disconnect the following from the system board:a. camera cableb. LVDS cablec. system-fan cabled. optical-drive cablee. hard-drive cablef. hard-driv

5. Remove the system board from the computer.Installing the System Board1. Align the system board on the computer.2. Tighten the screws to secure the

Removing the Display Bracket1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a. stand coverb. standc. back coverd. optical dr

4. Remove the screws that secure the display bracket to the computer. Lift and remove the display bracket from the computer.Installing the Display Bra

Contents1 Working on Your Computer...5Before Working Inside Your Compu

Removing the Camera1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a. stand coverb. standc. back coverd. optical drivee. har

4. Disconnect the camera cable from the camera and remove the camera from the computer.Installing the Camera1. Connect the camera cable to the camera.

3. Perform the following steps as shown in the illustration:a. Remove the screw that secures the microphone.b. Disconnect the microphone cable from th

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Table 1. Navigation KeysKeys NavigationUp arrow Moves to the previous field.Down arrow Moves to the next field.<Enter> Allows you to select a va

Option Description• Enabled Legacy Options ROMs (Default: Enabled)Date/Time Allows you to set the date and time. The changes to the system date and ti

Option DescriptionDefault Setting: All devices are enabled.Audio Allows you enable or disable the audio feature.• Enable Audio– Enable Microphone– Ena

Option Description• Confirm the new passwordStrong PasswordEnable strong password - This option is disabled by default.Password Configuration This fie

Table 5. Secure BootOption DescriptionSecure Boot Enable Allows you to enable or disable the Secure Boot Feature. The options are:• Disabled (Default)

Option DescriptionLimit CPUID Value This field limits the maximum value the processor Standard CPUID Function will support• Enable CPUID Limit (Disabl

Removing the Camera...30Installin

Option Description• LAN Only• WLAN only• LAN with PXE BootThis option is Disabled by default.Block Sleep Allows you to block entering to sleep (S3 sta

Table 11. MaintenanceOption DescriptionService Tag Displays the service tag of your computer.Asset Tag Allows you to create a system asset tag if an a

Option DescriptionNOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServ

6. Select your computer model and the Product Support page of your computer appears.7. Click Get drivers and click View All Drivers.The Drivers and Do

3. Select System Password , enter your system password, and press <Enter> or <Tab>.Use the following guidelines to assign the system passw

5Technical SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. F

Feature SpecificationDiscrete 1 GB DDR3Table 17. AudioFeature SpecificationController ALC3661-CG (Realtek)Speaker single 4-ohms, 2 W AVG speakers with

Table 21. DrivesFeature SpecificationHard drive one 2.5-inch SATA driveOptical drive (optional) one DVD-ROM, DVD+/- RWTable 22. Ports and ConnectorsFe

Table 24. Camera (optional)Feature SpecificationImage resolution 0.92 megapixelVideo resolution 720p @ 30 FPS HDDiagonal viewing angle 74 degreesTable

Feature SpecificationBack panel:Link integrity light on integrated network adapter :Green — a good 10 Mbps connection exists between the network and t

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

6Contacting DellContacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, pack

To avoid damaging your computer, perform the following steps before you begin working inside the computer.1. Ensure that your work surface is flat and

Turning Off Your ComputerCAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.1.

2System OverviewFigure 1. Inside View – 11. memory shield2. system board shield3. bottom cover4. power-switch board5. hard drive6. VESA Bracket7. opti

Figure 2. Inside View – 21. WLAN card2. memory module3. power supply unit4. system board5. speaker6. display bracket7. system fan8. heatsink9. camera1