Model: P2715Q/P2415QRegulatory model: P2715Qt/P2415QbDell P2715Q/P2415QUser’s Guide
10 | About Your MonitorMonitor SpecificationsFlat Panel SpecificationsModel P2715Q P2415QScreen type Active matrix - TFT LCD Active matri
About Your Monitor | 11Preset Display ModesDisplay ModeHorizontal Frequency (kHz)Vertical Frequency (Hz)Pixel Clock (MHz)Sync Polarity (Hori
12 | About Your MonitorElectrical SpecificationsVideo input signals •Digital video signal for each dierential line. Per dierential li
About Your Monitor | 13 With stand assembly and cables7.53 kg (16.60 lb) 5.68 kg (12.52 lb) Without stand assembly (for wall moun
14 | About Your MonitorPower Management ModesIf you have VESA’s DPM-compliant video card or software installed in your PC, the monitor ca
About Your Monitor | 15Pin AssignmentsDP connector (in) Pin number 20-pin side of theconnected signal cable1 ML3(n)2 GND3 ML3(p)4 ML2(n)5
16 | About Your MonitorDP connector (out) Pin number 20-pin side of theconnected signal cable1 ML0(p)2 GND3 ML0(n)4 ML1(p)5 GND6 ML1(n
About Your Monitor | 17mDP connectorPin number 20-pin side of theconnected signal cable1 GND2 Hot Plug Detect3 ML3 (n)4 GND5 ML3 (n)6 GND7
18 | About Your MonitorHDMI connectorPin number 19-pin side of theconnected signal cable1 TMDS DATA 2+2 TMDS DATA 2 SHIELD3 TMDS DATA 2-
About Your Monitor | 19MHL connectorPin number 19-pin side of theconnected signal cable1 N/C2 CD_SENSE3 N/C4 N/C5 TMDS_GND6 N/C7 MHL+8 MHL_
NOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates potential damage to hardware
20 | About Your MonitorUniversal Serial Bus (USB) This section gives you information about the USB ports available on your monitor.Your c
About Your Monitor | 21Plug-and-PlayYou can install the monitor in any Plug-and-Play-compatible system. The monitor automatically provides t
22 | Setting Up the MonitorSetting Up the Monitor
Setting Up the Monitor | 23Connecting the DP (or mDP) cable Connecting the HDMI cable(Optional)Connecting the USB cable
24 | Setting Up the MonitorConnecting the Monitor for DP Multi-Stream Transport (MST) functionSecondary Monitor Primary Monitor NOTE: S
Setting Up the Monitor | 25 3 Turn on the monitor and the MHL source device. 4 Select input source on
26 | Setting Up the MonitorAttaching the Cable Cover NOTE: The cable cover is detached when the monitor is shipped from the factory.
Setting Up the Monitor | 27Removing the Cable Cover 1 Press the tab on the cable cover. 2 Remove the two tabs on the bottom part
28 | Operating the MonitorOperating the Monitor
Operating the Monitor | 29The following table describes the front panel buttons:Front-Panel Button Description1Shortcut key: Preset ModesUse
ContentsAbout Your Monitor ... 5Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30 | Operating the MonitorUsing the On-Screen Display (OSD) MenuAccessing the Menu System NOTE: Any changes you make using the OSD menu
Operating the Monitor | 31Icon Menu and SubmenusDescriptionBrightness/ContrastUse this menu to activate Brightness/Contrast adjustment.Brigh
32 | Operating the MonitorIcon Menu and SubmenusDescriptionHDMI (MHL) Select the HDMI (MHL) input when you are using the HDMI connector.U
Operating the Monitor | 33Icon Menu and SubmenusDescriptionPreset Mode When you select Preset Modes, you can choose Standard, Multimedia, Mo
34 | Operating the MonitorIcon Menu and SubmenusDescriptionAspect Ratio Adjust the image ratio to Wide 16:9, 4:3, or 1:1.Sharpness Makes
Operating the Monitor | 35Icon Menu and SubmenusDescriptionUSBSystemMonitor status On Standby OffMonitor with upstream connectedOn (Disabled
36 | Operating the MonitorIcon Menu and SubmenusDescriptionLock Controls user access to adjustments. When Lock is selected, no user adjus
Operating the Monitor | 37Icon Menu and SubmenusDescription OtherSelect this option to adjust the OSD settings, suchas the DDC/CI, LCD con
38 | Operating the MonitorIcon Menu and SubmenusDescriptionReset Other SettingsRestores other settings, such as DDC/CI, to factorydefaul
Operating the Monitor | 39This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor
4 | Contents Troubleshooting ...43Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . .
40 | Operating the MonitorIf either DP, mDP or HDMI (MHL) input is selected and the corresponding cable is not connected, a floating dial
Operating the Monitor | 41Using the Tilt, Swivel, and Vertical Extension NOTE: This is applicable for a monitor with a stand. If you purch
42 | Operating the MonitorRotating the MonitorBefore you rotate the monitor, your monitor should be fully vertically extended (Vertical E
Troubleshooting | 43Troubleshooting
44 | Troubleshootingor 4 This box also appears during normal system operation, if the video cable becomes disconnected or dam
Troubleshooting | 45 4 Carefully inspect the screen for abnormalities. 5 Press Button 4 on the front panel again. The color of the
46 | TroubleshootingCommon SymptomsWhat You ExperiencePossible SolutionsIntermittent ProblemsMonitor malfunctions on & off•Ensure th
Troubleshooting | 47Product Specific ProblemsSpecific SymptomsWhat You ExperiencePossible SolutionsScreen image is too smallImage is centere
48 | TroubleshootingSpecific SymptomsWhat You ExperiencePossible Solutions2 Use the or button to highlight “DP” or “mDP”3 Press and
Appendix | 49Appendix
About Your Monitor | 5About Your Monitor
50 | AppendixSetting Up Your MonitorSetting Display Resolution to 3840x2160 (maximum)For best performance, set the display resolution t
Appendix | 51Maintenance GuidelinesCleaning Your Monitor WARNING: Before cleaning the monitor, unplug the monitor power cable from
6 | About Your Monitor DP cable (mDP to DP)•Drivers and documentation media •Quick Setup Guide•Safety and Regulatory Information•Fact
About Your Monitor | 7Identifying Parts and ControlsFront view Label Description1 Function buttons (For more informatio
8 | About Your MonitorBack View
About Your Monitor | 9Bottom View Label Description Use1 Stand lock Lock the stand to the monitor using a M3 x 6 mm screw (screw not incl
Kommentare zu diesen Handbüchern